Calibrating the ESCs on a 2-motor-plane?
@MickeM wrote: Hi, I have a plane with two motors, each with its own ESCs. Using Pixhawk 2.1 and ArduPlane 3.9.5. How do I calibrate the ESCs? Alternative 1. In Mission Planner there is an ESC...
View ArticleClik here to view.
737MAX8 Lion Air flight data (FDR?) log
@Andrew_Rabbitt wrote: Interesting… I think ArduPlane is smarter than Boeing’s flight control software… Posts: 1 Participants: 1 Read full topic
View ArticleWind observation error with inbuit simulator
@ujjwalrathod007 wrote: Hello, I have a doubt… I have plotted the Wind observed by ArduPlane with inbuilt simulator and JSBsim FDM. I ploted both of them but the wind observed by inbuilt simulator is...
View ArticleTransition in ArduPlane
@Gerald_K_Antony wrote: Hey Everyone, Is it possible to transition from a quadcopter to a tri-copter using pixhawk on air (Instead of plane to quad etc). Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Problem Sonar and missionplanner
@cristianoris wrote: Good morning everyone I have a problem with a Sonar and the application. I have the sonar installed, the status LED indicates that it is working correctly. But the application...
View ArticleNo yaw indication on radio calibration page
@Smallboy808 wrote: Hello guys, I’m having a problem with getting the yaw indicator on the radio calibration page to move when I move the rudder stick on my controller. The indicator stays at 1500ms....
View ArticleWhy aren't the control surfaces activated to assist attitude control during...
@Illini_Rob wrote: Hello, I am a relatively new user. Pixhawk 2.1, Arduplane, latest firmware, etc… I am currently flying a QuadPlane conversion of a Radian Pro with good results so far. I am...
View ArticleCustom made IR RPM sensor
@nicolaufg wrote: Hi all, I built myself an infrared RPM sensor (although I’m quite bad at electronics). It works well with a teensy and I can quite accurately read the RPM with a custom program for...
View ArticleHow to slow airspeed done on approach & landing
@jstarch wrote: When performing an autolanding how do you get arduplane to slowdown the fixwing? PF_ & LAND_ airspeed parameters seem to have no affect. Note: I am using an airspeed sensor. Posts:...
View ArticleF405-Wing-Talon mini win't fly in stabilized modes
@Jeremiah_Smith wrote: I’m hoping someone can give me some tuning insight. I been working on getting this airplane flight worthy for about 6 months. I have quite a few struggles ranging from servo...
View ArticleTelemetry radio (MicroHard) is only connecting after preflight reboot shutdown?
@Duran_De_Villiers wrote: Hello all. We’re having issued connecting our VTOL to mission planner via a Microhard radio on TCP, we get full connection via QGC with exact same settings/hardware, but via...
View ArticleSuggestions for channels
@MartyMcFly wrote: Ive been used to arducopter for years and am now doing a plank and A small VTOL im woundering if it would be possible to have the flight modes extra functions so we can set them on...
View ArticleSlower throttle response in AUTO modes
@Glen wrote: I would like my planes to be more efficient in AUTO modes. Unfortunately the throttle response for the TECS systems is so quick with modern ESCs that a lot of energy is wasted ramping up...
View ArticleTelemetria simultanea
@abraham_saucedo wrote: Hola a todos: Soy nuevo en este mundo de los drones , y quería saber si se puede recibir los datos de telemetria simultáneamente en el transmisor y en la estación en tierra....
View Article915 Mhz telemetry jumping connection with ground station
@CullenChong wrote: Hi there my buddy and I are building two planes using pixhawk cube with 915Mhz telemetry. We found if one of us has our plane connected to our GCS through the 915Mhz radio and the...
View ArticleClik here to view.
How to program one mission that the drone VTOL starts again and flies back...
@Aticof wrote: How do you program one mission that the drone VTOL starts again and flies back after the payload has been removed without other CGS in destination? Could the mission be done like this?...
View ArticleBRD_SD_SLOWDOWN parameter
@vascodx wrote: Hi! BRD_SD_SLOWDOWN parameter allow microSD cards to be run at a lower clock to improve reliability, defaults to 0. I like to always set LOG_BITMAST to 65535 on the Cube with the...
View ArticleExternal Presure/temp Sensor MS5611
@Montville wrote: Hello there, I have just purchased 2 x MS5611 to enable me to obtain external pressure and temperature from my plane. I follow instructions on this page-...
View ArticleArduPlane issues with Pixhawk1 and ChibiOS
@phokur wrote: Hello all! I haven’t been able to build a working version of Plane for my Pixhawk1. Last time I compiled and uploaded to my board was around a year ago. Now if I build master (I’ve...
View ArticleDigital Airspeed Sensor Not Measuring Airspeed
@Gclements10 wrote: Bought a new 4525D digital Airspeed Sensor to use with a fixed wing glider. I have a pixhawk 4 flight controller and have connected the sensor directly to the I2C Port. I’ve set...
View Article