Clik here to view.
I lost connection from the plane suddenly in the middle of the mission. no...
@Artem_Skorsky wrote: HI, for some reason, i lot the plane suddenly when it was doing surveying mission. suddenly i lost the telemetry, while it was around 500 m away from me. and there was no data...
View ArticleMatek 405 wing loging
@MartyMcFly wrote: Hi can A Matek 405 wing do loging with a sd card inserted many thank’s Posts: 1 Participants: 1 Read full topic
View ArticleSafety switch activated in flight
@air-tito wrote: Hi, last thursday I did the maiden flight of my Believer on Arduplane 3.9.6 with the Cube. It took off (auto takeoff) and 2 or 3 seconds later switched to safe mode, and obviously it...
View ArticleAdding mavlink statustext to FrSky passthrough telemetry
@juichi wrote: So I’ve been messing around with companion MCUs/Computers and ArduPilot. One of the things that I would like to do is send a statustext message from the companion machine to the flight...
View ArticleCan't arm rear motor on vectored yaw tricopter
@pfaudette wrote: I’m using a Pixhawk 2.4.8 with Arduplane V3.9.6, and can’t seem to get the rear motor going. I’ve got it setup on SERVO7_FUNCTION,35. But in MP under the Servo Output tab, I only get...
View ArticleCan APM be used for a glider?
@allen2 wrote: wanted to do some mission by dropping the glider motorless plane. just wanna ask if anyone here did the flight mission on pixhawk 2.1? Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
How to get the telemetry data on the mission planner?
@Ricardo_Junior wrote: I need the RSSI and distance home data (telemetry logs), but when I convert to TXT, MAT or CSV the distance home data does not appear how do I extract this data from telemetry...
View Articleomnibusf4v3 s.port only gps sensor
@oguzhan wrote: hi. i installed last arduplane on my board. everythings works fine execpt telemetry. i have r9m and r9 slim+ set. r9 slim+ has inverted s.port out. i connected tx1 to inverted...
View ArticleHardware in the loop apm 2.6
@mahdi.yaich wrote: hardware in the loop apm 2.6 wath is the problem ??? i’am using just apm 2.6 + gps + compass indoor Posts: 4 Participants: 2 Read full topic
View ArticleSome question for ArduPlane3.9.6 chibios
@alphasion wrote: just download and upload the ArduPlane-3.9.6 with ChibiOS and i found there is 7 Serial Port in the param list. so could someone can tell me which port is the Serial 6 in pixhawk v1,...
View ArticlePlane 3.9 with OpenPilot Revo for gliding
@glassfish wrote: Hello. A couple months ago I posted about an autonomous gliding project I am working on and I received some helpful tips on setting up Ardupilot for the mission. However, when it...
View ArticleArduplane with Frsky R9 MM FC Omnibus F4 V6 or Frsky RXSR FC Omnibus F4 V6
@HighFlyer wrote: Has any successfully used Arduplane with the Frsky R9 MM FC Omnibus F4 V6 or Frsky RXSR FC Omnibus F4 V6. The Frsky website only talks about Betaflight but I have a couple of fixed...
View ArticleQuadPlane（ 2 front motor tilt）transition yaw swing
@MarcoChan wrote: Hello everyone，I build a quadplane which has 4 motor and two front motor can tilt.I follow the quadplane document to setup my aircraft. Now my quadplane work fine in QSTABLIZE and...
View ArticleTight and Low Autolandings
@garlandk wrote: Have not flown my Cube Anaconda in a while and decided to take her out today. I loaded the latest firmware and took her to the field. I decided to see if I can do low and tight auto...
View ArticleAutomatic Hatch Open/Close
@Matt_C wrote: I have a camera mount system that I have 3d printed and it includes a cover for the lens. I remember reading that there was going to be a function for automatic landing gear that could...
View ArticleDoing Autotune, flying wing almost crashed, entering in uncontrolled dive
@NorbertK wrote: It was an Atotune session, windy day up to 25kmh wind, AR wing entered in a dive, switched to manual flight in LOS and with great luck managed to stabilize it at minus 19 meter. I`m...
View ArticleSuccessful VTOL Transition! Would like help tweaking!
@Chad_Frazer wrote: Today at 11:53AM Local Time I completed by first VTOL transition! Then I landed, swapped batteries and did it again! WOOOTT!! Here are the telemetry and apm logs location. What...
View ArticleNo GPS but the plane still continue the mission
@Hadits_Baroya wrote: Hello guys, i have a problem with the GPS. so here is the detail : i want to test my plane before going to do some mapping job. (test the auto flight mode) i’m using The Cube...
View ArticleClik here to view.
Plane 3.9.7 released
@tridge wrote: ArduPilotPlane.jpg750x291 33.1 KB This is a minor release to fix a single important bug in speed/height handling. The bug was in the TECS (total energy control system) and could cause a...
View ArticleProblem following the track
@bendead wrote: Hi I am using a Foxtech Nimbus VTOL on 3.9.5 and during my survey, the plane was nearly everytimes 10m on the side of the track. You will be able to find the two kmz here :...
View Article