Skywalker X8 Crash
@rijun034 wrote: It is very sad to say that my Skywalker X8 flight got crashed. Incident: Hand Launched. Used only Throttle stick. Plane started to glide and suddenly it rolled left and crashed. After...
View ArticleHow to align the FC board for level flight
@Taipan wrote: I am in the process of fitting an Omnibus F4 Pro flight controller to a Bixler 3 and I need to make sure that the flight controller board is mounted “level” with the Bixler 3. I assume...
View ArticleArduPlane v3.9.1 on an Omnibus Pro F4 v3 RC channel mixed up with R9 mini and...
@martinlta wrote: Hi I have installed ArduPlane v3.9.1 on an Omnibus Pro F4 v3. I have soldered the ppm PPM solder pad/resistor and in Mission planner I haver RC inputs from the receiver(R9 mini sbus...
View ArticleNeed help analyzing crash logs
@artemen wrote: Been using aircraft in question with AP3.9.1 since it was released (20-30 flight hours) without any issues. Updated to 3.9.2 a week and a half ago nothing else changed. First flight on...
View ArticleClik here to view.
Plane 3.9.3beta release
@tridge wrote: ArduPilotPlane.jpg750x291 33.1 KB This is the first beta release for the 3.9.3 firmware. This release has the following changes over 3.9.2: fixed error handling for corrupt RC input...
View ArticleClik here to view.
ChibiOS 3.9.2 Analog airspeed and HUD pitch change
@hangarspace wrote: I’m putting together a Matek F405 Wing with ChibiOS Arduplane, and yesterday I looked at adding an analog airspeed sensor. I’ve previously used these on APM’s and digital ones on...
View ArticleTilt rotor planes configuration
@martinlta wrote: I am looking at tilt rotor plane confguration in the plane docs. Ok with frame class as 7 tricopter. But what is the frame type for 2 motors vectoring up together and a rear motor...
View ArticleDual Tilt-Wing issue
@glacier051 wrote: Hello: Need a little hand holding here. I’m building a quad tilt-wing. I’ve flown the frame as a quad, using Copter. I have the latest Plane installed now and the Q functions...
View ArticleChanging Flight mode at power up
@tucuman79 wrote: Hi, I search in the forum but i couldn’t find a solution for an issue. When I power up my Pixhawk 2.1 it starts in RTL mode and servos moves continuously, I like to startup my plane...
View ArticleOctaplane simulation Realflight 8 or Xplane 11
@arjun7965 wrote: Hi, I am trying to make a simulation model in Xplane 11 or Realflight for an octaplane with 2 forward puller motors (so a total of 10 motors). I just wanted to know if ardupilot...
View ArticleNeed help - Plane crashed on turning. No Idea why
@Nihal wrote: Hi, My XUAV Talon that has flown for over 30 hours without issue fell out of the sky when performing a corridor mission. There were no changes to the setup. It had flown properly just an...
View ArticleWhat happen when tilt-quadplanes with all four motors tilting
@aziz_kountche wrote: hello , what happen when i chose quadplane with all four motors tilting ? in fixed wing mode did the 4 motors run to push airplane forword ? or just the 2 front motors ? Posts: 1...
View ArticleNew Custom Library
@sripad_sahu wrote: Hello, I am trying to add new Custom Libraries into the ArduPIlot. So I added all the files to the Libraries folder and then imported all the Libraries from GCS_MAVlink.h. But when...
View ArticleClik here to view.
Plane 3.9.3 stable release
@tridge wrote: ArduPilotPlane.jpg750x291 33.1 KB The ArduPilot development team are delighted to announce the 3.9.3 stable release of the ArduPilot plane code. This release includes a number of small...
View ArticleClik here to view.
LOITER Autothrottle works wrong (not as discribed in Wiki)
@lorbass wrote: When I want to descend in Loiter Mode by Stick input of Pitch the Wing descend but proportionally to the difference to the original altitude the THR_OUT increase up to THR_MAX and of...
View ArticleAbout GPS_Time convertion to UTC time
@Brian_Duvall wrote: Hello, I recently figured out how to convert the epoch time from my arduplane data flash logs in matlab. The problem is it looks like I was flying for four days! lol. I know the...
View ArticleEngine Throttle Always High During Auto mode
@saadmir wrote: I am flying 2000mm wingspan trainer fixed wing with a gasoline engine fitted with Pixhawk Cube (Plane 3.8). Issue I am facing is of Throttle during Auto mode which stays at high...
View ArticleDo i need to redo all configuration after firmware update?
@allen2 wrote: any though on this will appreciated. im afraid facing another problem again. Posts: 1 Participants: 1 Read full topic
View ArticleArduplane camera mount manual control in Auto mode
@JeyPi wrote: Issue details If flying Arduplane in Auto mode it is possible to control the mount manually. But only until there is a programmed mission mount command like DO_MOUNT_CONTROL (sets the...
View ArticleClik here to view.
Yaw (and plane) out of control in auto modes (ATT.Yaw)
@RogerR wrote: Flew an auto mission the other day and the plane went crazy. After hitting a few waypoints, it erratically headed in the wrong directions for about two minutes. I switched to RTL and...
View Article