Reversed current measurement
@danielschafer wrote: This is a feature request! I read about a request on Gitter.im about reversed current measurement on the power module. And I thought this would be a great feature for the solar...
View ArticleClik here to view.
Elevon oscillation plus compass problem
@anparkinson wrote: I have a Pixhawk on a large wing so using elevons. I ran Autotune and it seems pretty good but about 25 minutes into an Auto flight I got a bit of oscillation. being elevons it’s...
View ArticleCan't find SERVO1_Function
@Maxwell_Wang wrote: in my full parameters i cannot find the SERVOn_Function also i all controls in the servo output page are grayed out and i can’t access them Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Plane 3.9.0beta2 released
@tridge wrote: APMPlane.jpg750x291 24 KB This is the second in a series of beta releases for plane 3.9.0. It is a major release, with a lot of changes. Builtin OSD support on boards with MAX7456 OSD...
View ArticleFlashing F405 boards - The easy way
@gtrick90 wrote: Hi guys, just to let you know a simple wy to flash F405 based boards with APM fw: you can use the Firmare utility integrated in the Betaflight/Cleanflight/Inav configurators Choose...
View ArticleClik here to view.
Failed to create log - won't log this session
@anparkinson wrote: I get this message on Mission Planner with every flight. I’ve tried different micro SD cards, formatting them, even swapping Pixhawks but always the same which makes me think it...
View ArticleHere+ compass not calibrated
@weliwarmer wrote: My RMRC Anaconda has 16 flights and over 4 hours of air time without any problems. No hardware change and in the same airfield as other tests the plane will not arm because the...
View ArticleESC beeping continually
@Luis wrote: Hi all , I am a new user of pixhawk mini FC. I have used APM planner to install Arduplane 3.8 for a new project of FPV fixed wing. After initial setup, all it is OK except ESC...
View ArticleAnalog airspeed vs battery monitor on F405-WING
@sanyok48 wrote: I am really stuck on setting up analog airspeed sensor on Matek F405-WING with Ardupilot firmware from here http://firmware.ardupilot.org/Plane/latest/MatekF405-Wing/. It works really...
View ArticleClik here to view.
Albatross Tuning Help
@FringerRinger wrote: Hi there - long time user but mostly just for fun. Been flying an RMRC Anaconda for some time but just stepped up to an Albatross. It’s huge. Anyway, they seem to use PX4 for...
View ArticleGEOFENCE check before ARMING
@sripad_sahu wrote: Hello, I want to check whether the plane is inside the GEOFENCE, and if not inside the geofence then it should not ARM at all. ANY suggestions on how to achieve that? Basically I...
View ArticleChange Configuration while operating
@Mathis wrote: Hi, I’m trying to build a plane, with tiltable wings. The plane is supposed to have 4 wings (front and back) with 2 Motors on each wing. Resulting in a total of 8 motors. On each wing,...
View ArticleClik here to view.
Plane crash - altitude loss after climb and dive
@anparkinson wrote: My plane was on an auto flight using a Pixhawk running 3.8. It was flying at 25m then next waypoint up to 58 m to clear some pylons. The next waypoint was back to 25m but it never...
View ArticleClik here to view.
Crash after TAKE OFF 3.8
@bchristal wrote: Hi, Hoping I can get some feedback. I’ve had quite a few similar crashes. Flying wing executes TAKEOFF in AUTO. Heads to waypoint 1 and takes a dive. bin:...
View ArticleArduPlane problems on Beaglebone Blue
@mooseandelknstuff wrote: Hi, I followed the documentation to install and configure my Beaglebone Blue for ArduPlane, but it looks like I must have missed something: When I run the latest ardupilot...
View ArticleWeak stabilization
@Maxwell_Wang wrote: When switched into stabilized or mission modes control surfaces move very little and result in little to no movement. Radio control throws are ok but when testing by tilting plane...
View ArticleUsing SITL with python script
@sripad_sahu wrote: Hello, I want to use python script to connect to the SITL that is running on my system. This is the command i use to connect: from pymavlink import mavutil import time...
View ArticlePlane doesn't hold altitude in AUTO - Cannot change desired airspeed
@pawel260 wrote: Hi everybody, I have a question regarding arduplane altitude and airspeed control. In my setting, from time to time it happens that when doing mission in AUTO the plane doesn’t hold...
View ArticleChannel 7 & 8 option for RTL updates?
@Gromitvt10 wrote: I know this has been requested before, is there a status on when Arduplane will get this function like ArduCopter has? In the meantime is there a workaround? I want to put RTL on a...
View ArticleClik here to view.
Support for delta wing with canards and rudders
@JosuaB wrote: Hi there, I am doing some proactive research on the applicability of a Pixhawk 2.1 Cube in a UAV system that has a pretty abnormal design. We are working on a delta-wing type UAV, with...
View Article