Loiter radius far too large
@Inae wrote: Hi everybody, I have a 6m span glider (ASG29) equipped with a Pixhawk 3 and Arduplane 3.8 I use the Pixhawk manly for safety reasons: when the glider is to far or to high and I have...
View ArticleClik here to view.
CC3D STM32F4 based flight boards
@yak-54 wrote: I have number of these in quads CC3D with out barometer will they work ? 20180606_080736.jpg1224x1632 573 KB Posts: 1 Participants: 1 Read full topic
View ArticleMode switch not working with Spectrum Sat Receiver
@hfinkle wrote: DX9 work great, all channels, with Ar6600T and PPM encoder connect with Just the Spektrum Sat Receiver, all channel through 7 show up in the green and respond to input , from 1000 to...
View ArticleSupport for Eagle tree airspeed sensor
@Karthik_A wrote: Can we have support for Eagle tree airspeed sensor in this release? Thanks to the awesome dev team. Posts: 3 Participants: 2 Read full topic
View ArticleTfmini lidar benewake arduplane v3.8.5?
@alainlive wrote: hello i would have liked to know if the tfmini lidar benewake works with arduplane v3.8.5 thanks for your answers Alain Posts: 1 Participants: 1 Read full topic
View Article[SOLVED]Timer interrupted AUTO error
@Mustafa_Zeybek wrote: Hi all, I have got this error when I try to take off the fixed wing plane with auto mode. It was working before but today I get this error. Please help. Thanks....
View ArticleClik here to view.
Tiltrotor support for plane #2
@pompecukor wrote: This is just a new post to continue for the endlessly long topic that started a few years back in the Dev section Original topic here: Tiltrotor support for plane So who is doing...
View ArticleSetting up SITL on Windows
@ibrahimqazi wrote: Hello respected members! I am installing SITL on windows 10. when I reach this step > cd ~/ardupilot/ArduCopter > make sitl -j4 So it gives me the following error...
View ArticleClik here to view.
"DoubleBat" Innovative Kind of Power Supply For Quadplanes
@Rolf wrote: In our Tri-Tiltrotor VTOL “Mozart” we have now (>100 flights) killed several expensive high-performance batteries without ever having demanded power beyond specified limits....
View ArticleAPM 2.8 FrSky L9R RSSI
@Darryl_Engle wrote: I’m having bit of trouble getting RSSI to work. I’m using Mission Planner 1.3.56 and Plane 3.4.0. In 3.4.0 all I have to configure is RSSI_Range and RSSI_PIN. I have RSSI_Range...
View ArticleParameter for land into wind
@Braxton wrote: Is it possible to set the autopilot to land against wind, so the plane will stall and drop without reverse thrust. Airspeed sensor is equipped in the plane. I set the tecs_sink_max to...
View ArticlePré arm - Gyros Inconsistent
@Neodrone wrote: Hello everyone I have a problem that I can not solve. After all the initialization, if I delay to arm, the message “pre arm, gyros inconsistent” appears. I can only arm again if I...
View ArticleFBWA compensation is REVERSED/WRONG for Elevator
@jwcalvert wrote: I have read several topics about this issue but none seem to solve my problem. I am using: Arduplane 3.8.5 Pixhawk Taranis 9 Plus Bixler 3 aircraft Current behaviour: When I pick up...
View ArticlePlane on APM2.6 won't change modes; Copter works fine
@mooseandelknstuff wrote: Hi all, With any ArduCopter firmware I’ve tried on my APM2.6, the flight mode changes as expected with input to channel 5, confirmed by the green bar changing the highlighted...
View ArticleClik here to view.
MS5525 vs MS4525 airspeed sensor noise
@disgruntled-patzer wrote: Hello all, I am currently testing two types of airspeed sensors (MS4525DO and MS5525) to see which is more suitable for mounting on my aircraft. I noticed from the forum...
View ArticlePlane flips over when RTL engaged
@Jack_Roohan wrote: I have tried recalibrating a number of times with no avail, plane fly fine in manual mode but with RTL engaged plane flips over and ailerons jitter putting the plane in an upside...
View ArticleFX-79 VTOL, after transition have no contorle
@Roby wrote: Hi, I am new on this forum. I have searched on google an different forums an did`t find solution. I have Zeta Fx-79 buffalo converted to VTOL and Quad part works great. I have one FX-79...
View ArticleClik here to view.
Help with Pitch and Roll Tuning
@smonks wrote: I have am using the believer rc plane with an AUW of about 10.5 Lbs. I am still having a bit of difficulty getting some of the tunings correct. I believe my COG is perfect however one...
View ArticleWhat does Q_WP_RADIUS supposed to do?
@Echo wrote: I’m quite new with the quadplane and I’m trying to understand what does this parameter do. I’ve already read the description here:...
View ArticleArduPlane control via mavros/setpoint_cmdvel?
@HobbySingh wrote: What is the expected behaviour if I try to control fixed wing in guided mode using command velocities? Will it works as it works in arducopter as i if it maintains its current...
View Article