Automated Landing Overshoots Landing Spot
@flyingw wrote: I’ve been experimenting with airplane auto landings and have had multiple successful landings. Amazing. I’m using a Pixracer, Arduplane 3.8.4 and Mission Planner 1.3.56. I am using...
View ArticleClik here to view.
Tilt rotor stop in ACRO mode
@Ecoesp wrote: Hello, I am using Plane 3.9.0 on my X8 tricopter with pixhawk 2.1. I use a configuration of 3 rotors and they all have mechanical rotation. photo_2018-05-25_09-38-14.jpg720x1280 169 KB...
View ArticleQstabilize wrong
@Theerawit_Tekitchamr wrote: My diy plane is tailsitter with firmware V3.8.5 . After parameter were set up, I checked how elevon work with FBWA mode. Elevons were deflected correct,but in Qstabilize...
View ArticleList of available servo functions is incomplete
@wazoo22 wrote: I’ve been working with (lurking?) the tailsitter development thread, and I need to find a complete list of the possible servo functions. Somewhere in the past I came across such a...
View ArticleMoved to the 3.9.0 section - VL53LOX Rangefinder and Arduplane 3.9.0 (beta)
@flyingw wrote: Moved the the Arduplane 3.9.0 section. Posts: 1 Participants: 1 Read full topic
View ArticleVL53LOX Rangefinder for Landing Flare
@flyingw wrote: I am experimenting with and hope to use a VL53LOX rangefinder to help with determining the altitude at which to flare in an auto-landing. On the bench I observe that the unit can...
View ArticleServos do not move
@flyingw wrote: Had a plane with an mRo Pixhawk working prior on an earlier Arduplane release. I upgraded to Arduplane 3.8.5 now and set things up the same as before. But I cannot get the servos to...
View ArticleArduplane for twin engine edf jet with thrust vectoring?
@tomismrkolj wrote: Hi, I am building foamie su37 and want to use pixhawk or apm for flight stabilisation. These are flight controls: 2 ailerons, 2 elevons (=stabilators), 2 rudders and 2 vector...
View ArticleClik here to view.
Sudden uncommanded max pitch demand during auto
@Naterater wrote: Running 3.8.5 beta 3 (this was just before the 3.8.5 release) on a Cube. Pretty much everything is standard setup. Running RFD900’s. Believer twin-engine foamie. Plane is in the...
View ArticleThrottle on max pwm when disarmed
@igalg wrote: when I disarm my quadplane, all vertical motors go to idle, but the “pusher” motor (throttle, ch3out) goes to max pwm with release 3.8.5 on pixhawk2 does anybody else has similar...
View ArticleAutotune does not make adjustments
@Montville wrote: Hi, I have tried to do a autotune and have not noticed any changes in roll or pitch. I looked at the log as stated in the wiki also. Is there a setting which I need to select/change...
View ArticleFlight following?
@wkf94025 wrote: I am interested in air to air flight following, fixed-wing. Searching this forum for the exact phrase “flight following” there is only one post from 5 years ago. What am I missing?...
View ArticleClik here to view.
RTL does not stop decending
@Mr.1 wrote: Hi all (ardu) pilots, I have been flying ardupilot controlled multicopters for many years without any crash. This months, I tried arduplane for the first time. The pixhawk is installed on...
View ArticleSERVO_AUTO_TRIM recommended for permanent use in a foam plane
@Dagolaf wrote: SERVO_AUTO_TRIM sounds like a great improvement but from the few information I found it was not 100 % clear to me if it is expected to turn off after first use. As we all know, planes...
View ArticleStart gyro accelerometer / compass calibration with rc
@mauris wrote: I can’t calibrate with usb cable plugged… Could you say if a way to start calibration with rc exist ? Posts: 1 Participants: 1 Read full topic
View ArticleTwin motor crash
@armadillo wrote: Hello, today I had the pleasure of ripping a brand new Believer 1960 to shreds, possibly due to criminal stupidity. Let me start at the beginning. I had finished building the...
View ArticleClik here to view.
Wind calculation with Airspeed sensor totally off
@Steffen20 wrote: Hi there, I have a Ritewing Drak, fitted with a Pixhawk. I played a bit with the Cg, so that is why the plane was so untrimmed. But still flies really good. The Airspeed should be...
View ArticleAccelerometer calibration ouside the airframe
@wazoo22 wrote: As recommended, I calibrated my accelerometer on the bench ( worked), then reinstalled it in the airframe. Now I seem to be back to go. How do I know if it’s still holding the...
View ArticleQuadplane Testing
@ardisd wrote: Over he last few months months I have been building a quadplane - Tilt Motor version. I have done a successful flight in Qstabalize mode (https://youtu.be/dS3_w6jawXA), Has anyone...
View ArticleRescue function
@master-of-desaster-8 wrote: Hello together, I like to ask if there is a “Rescue function” avaiable in Ardu Plane? For example if I fly in Acro mode and someting goes wrong - switch back to FBWA and...
View Article