ArduPlane reverse thrust setup
@mirkix wrote: Hi, I replaced the ESC in my Plane running ArduPlane 3.8.0beta5 to a BlHeli ESCs with reverse enabled. When I am in manual mode, I now have to center the throttle stick to get zero...
View ArticleCannot configure Flight Mode 6
@flyingw wrote: Hi, I have experience with ArduCopter and am now configuring airplane with ArduPlane. My setup includes the latest Emlid Pi/Navio2, ArduPlane 3.7.1 and Mission Planner 1.3.48. In my...
View ArticleTwin motor/differential thrust with Ardupilot?
@marcmerlin wrote: I have a twin motor plane I haven't flown yet. I understand I can connect both motors to the same channel, and pretend it's a single motor plane, but that's kind of boring @tridge...
View ArticleMixing roll and pitch channels for multi-rotor setup in plane mode
@955E479 wrote: Hi - I have a 4 propeller drives, setup as ailerons under fixed wing plane FW (APM V.3.7.1), and operating exclusively as a function of roll angle through channels RC5..RC8 (See Param...
View ArticleLidar ALT in FBWB
@George_Muirhead wrote: will FBWB mode use the lidar for altitude data? i want to use it for the minimum altitude. Posts: 1 Participants: 1 Read full topic
View ArticleAnother topic about pitot needed or not
@Andres_Abrego wrote: Few pilots in my area discuss if the wind speed sensor is really needed or not for autonomous flight, i have been flying for almost a year more or less successfully without it,...
View ArticleE-flight converge default file
@rmackay9 wrote: I've created a default parameters file for the E-Flight convergence that I flew on the weekend. This file is actually from Tridge who has also flown it. github.com...
View ArticlePixhawk 2.1 Elevon Servo acting erratic
@marvinlange wrote: After pushing the safety switch my left Elevon Servo is constantly moving it was locking hard over switched to Opti ESC and separate Bec now it just sits thier and agitates but...
View ArticleOctaquadplane: power loss / yaw
@Anthony wrote: I'm seeing some strange loss of power in VTOL. I think I'm chasing a yaw problem where the vehicle is trying to correct some yaw error but I'd like to have somebody more qualified take...
View ArticleDeltawing // no servo response
@Alex77 wrote: Dear community, i'm using a Deltawing (Tuffwing) with a Holybro "Pixhawk" and a FrSky X4R receiver. ArduPlane 3.7.1 with MP 1.3.48. The servos work properly if connected to the receiver...
View ArticleCan't find ELEVON_OUTPUT param
@varkokonyi wrote: Hi! I'm trying to set up my flying wing, but I cannot find the ELEVON_OUTPUT param. I tried searching it with the "Find" option, no results. What am I doing wrong? ArduPlane 3.7.1,...
View ArticleAfter Autotune plane out of control at take off
@lucamax wrote: I have a very little experience with planes and the plane is a little bastard, a 60 cm delta wing , Skywalker X1, 300 grams, the plane was flying well in FBWA even if turns were very...
View ArticleCamera always triggered event not in mission
@aidil wrote: HI all,can anyone help to solve this problem.i'm trying to triggring camera using Seagull Map2 for mapping.The problem is when i'm arm my plane, the pixhawk always sending triggering...
View ArticleCamera Shutter always triggering in MP
@aidil wrote: Hi all,I have a problem to use camera shutter in MP.I'm using Seagull MAP2 to convert servo signal to sony RX100 signal to triggering camera.After i set the shutter channel (i'm using...
View ArticlePixhawk 2.1 Not Motor RPM untill 35 to 40% throttle on Stick
@marvinlange wrote: For some reason my Motor dos not start spinning until after 35 to 40% on StickThings I have tried2X Calibrate Radio3X ESC Calibration using this Method...
View ArticleSF11 Lidar working over I2C w/ 3.7.1?
@CJ_ASW wrote: Due to I2C sonars no longer working on the second I2C bus of Pixhawk 2.1 (https://github.com/ArduPilot/ardupilot/issues/5831), I just purchased Lightware SF11 lidar units for my planes....
View ArticleFailsafe turns off engine
@junsonic67 wrote: I have an APM2.8 this is configured plane v3.7. When I execute the failsafe on ground I turn off the Rt transfer to RTL there all things OK but it turn off the engine. I changed...
View ArticleWhen I add variable in ardupilot, firmware can not be passed compilation
@fightinghui wrote: Now I plan to use RC6 to switch on/off a servo. I try to add variable in https://github.com/ArduPilot/ardupilot/blob/master/ArduPlane/Parameters.h. I have created a file and add...
View ArticleNear fly-away. Altitude problem
@dellarb wrote: Had a scary near fly-away today flying ArduPlane on a X-UAV Talon air-frame. Setup is Pixhawk 1 with usual GPS, Compass, I2C Airspeed, PM and 900Mhz telemetry. Talon has flown many...
View ArticleCG and Autolanding with retractable gimbal
@Captain wrote: Hi We are using a retractable gimbal, the retract weight is like 400g near the CG. The difference between non retract and retract result a slight nose heavy. We will do auto tune when...
View Article