Flaps and Ailerons in Arduplane
@Rusty_Jones wrote: Flaps and Ailerons in Arduplane This probably applies to all recent versions of Arduplane, so hopefully someone can clear things up a little for me. I am installing a Pixhawk in a...
View ArticleFailsafe Issue: My ESC shuts off Completely, not what I want, help
@jwcalvert wrote: I am building a Plane Drone with a Pixhawk, Taranis Plus Radio and X8R Receiver. Everything is setup through Mission Planner and it all seems to work including GPS, GCS link, radios,...
View ArticlePixhawk and Spektrum AR9020 Receiver not communicating
@HanHan wrote: Hi, I have a Spektrum AR9020 receiver connected to the Pixhawk RC IN port using a PPM Encoder. The receiver is receiving power from pixhawk (as the receiver light is up), and i managed...
View ArticleEffect of wind on mapping/task speed
@jacques_eloff wrote: Most of my mapping work to date has been done in calm'ish conditions and when there is wind, I always try setup my legs cross-wind to get consistent ground speed and thereby make...
View ArticleRC Channel Trim not enough!
@semo wrote: hi , when I do the trim from the radio it move from the center to the full trim about (12% ) ex. throttle I want more limit in the trim . any help in how to do it ?? regards . Posts: 1...
View Article3 palnes,3 pixhawk,3 crashes. with logs
@omri wrote: Hi!I need your help, 3 planes of my crashed in a row...the same simptomes on the 3 crashes, the plane loss of height very fast with no option to control, twice it was on manual mode. I...
View ArticleHow many channels supported on PPM RC input?
@pauljatherton wrote: I have a ULRS Rx in my plane connected its 16ch PPM output to the Pixhawk (lite) FC, but can only see 12 channels in Mission Planner (ch13in-ch16in all show 0). Is 12 channels...
View ArticleNose over after mode change
@VUAS wrote: I have encountered an interesting issue where when I switch between modes the aircraft puts its nose down (approx 20 degrees) and keeps it there until I manually pull up. I first...
View ArticleLoiter cannot get to desired altitude
@michael_john wrote: After changing to Arduplane 3.7.1 and Pixhawk2, my airplane is having problems getting to the desired altitude on loiter.I have setup a regular mission with takeoff, loiter to a...
View ArticleQuestion Vtol Osprey
@Mangee wrote: I see in the development category that VTOL tilt wing and quad plane code is being worked on.I am building a QR-7 Shadow and then an OV-10 Bronco with designs for Osprey style.Question...
View ArticleWeird loss of roll control in FbwA, then RTL got away from home!
@Adolfo_Cobo wrote: Hello to all, I would appreciate your help with this weird crash we had with a Bormatec Maja plane with arduplane 3.7.1 in a Pixhawk. We checked everything before take off, and...
View ArticleFailsafe only if radio AND telemetry link fails?
@akolobov wrote: Hello, Is there a way to configure ArduPlane to trigger failsafe only if either (i) the aircraft is in Manual/Stabilize mode or (ii) both the radio and the telemetry link fails? Based...
View ArticleClik here to view.
Problem with V-Tail plane
@tiana wrote: Hello, I have problem with setting up V-Tail plane, when moving the plane on "YAW" shown on the picture below the tail not moving. I think this is not normal. Am i right? When outside...
View ArticleClik here to view.
How to install Arduplane 3.7.1 with the integrator reset bug fixed
@Adolfo_Cobo wrote: Hello to all, I was trying to understand a crash with Arduplane 3.7.1 ocurred when we switched to RTL, and the plane put itself at 90deg ROLL and entered a "spiral of death" and...
View ArticleClik here to view.
Using auto takeoff and auto landing, but without a full mission?
@marcmerlin wrote: Hi @MagicRuB,I'll post here since the answer can help othersRight now I have to have an auto mission for auto takeoff, which is the most valuable for me since I can't hand fly while...
View ArticleCan fixed wing and delta wing model be transformed each other by switch of...
@fightinghui wrote: Hardware Pixhawk Software ArduPilot-3.7.1 Hello, everyone. I want to ask for some questions. Can fixed wing and delta wing model be transformed each other by switch of radio? Fixed...
View ArticleCompass Motor Calibration for QuadPlane
@ferdicakmak wrote: I am trying to do "Compass Motor Calibration" for my QuadPlane using Pixhawk and ArduPlaneV3.8.0beta5. When I press button MP says "Unsupported preflight calibration". Is it...
View ArticleAPM Plane 3.3.0 Firmware still exits? For the board APM 2.6
@jedi_erdi wrote: Hello to all,I am planning to use the board APM 2.6 for a fixed wing UAV. I want to install the Mission Planner which is given in the link...
View ArticleChanging the behavior of flare to be more like a deep stall
@Pedro_Henrique_Silva wrote: Hello, guys I'm new to this dev environment, I just managed to compile my first firmware.Currently, I'm using Arduplane 3.6 and landing with rev_thrust. But sometimes,...
View ArticleClik here to view.
Rolling takeoff veering and log data
@charles_c wrote: Hi,We are currently trying to tune our plane for automatic takeoff. It is a 10kg tricycle plane, with the motor at the front. It tends to veer away from where it was pointing a few...
View Article