Hott telementry with F765-Wing not working for me
@guidohuelsmann wrote: Dear all, sorry to raise this topic again, but after trying out 4.0.9 stable, 4.1 beta and 4.1 latest. Tried also different receivers. Everything without success. Is it...
View ArticleExport / Import parameter form two diferent flight controllers
@Bernardoualidrones wrote: Hi everyone, Im changing my dron flight controller from a CUAV V5+ to a CUBE ORANGE. The drone already was flown by the previeus owner with the current parameters and...
View ArticleAre Differential spoilers behave as Auto Flaps?
@Elka wrote: Good day to all🛩️ Are differential spoilers considered as Auto Flaps by the autopilot and automatically managed by it in Auto mode or during autolanding? or setting differential spoilers...
View ArticleBad launch auto and crash
@glebivanov wrote: Hello. I use Arduplane 4.0.9. I have a problem. I have a point-by-point mission. Takeoff in auto mode with hands. But sometimes, during takeoff, the plane tilts very much to the...
View ArticleElevon and differential - possible?
@nostromo123 wrote: Differential on spoilers and ailerons is described in the documentation, but on elevons and differential I could not find a statement. Is that not possible? br KH Posts: 1...
View ArticleStall and airspeed parameter
@SlickShot wrote: hey guys, I have recently played with airspeed for my arduplane. I noticed my plane behave differently when I set (previous setup was on default value) : first try : FBW_ARSPD_MIN =...
View ArticleWs2812 on matek F405wing setup
@xixijoe wrote: Hello, is ws2812 working on F405wing now? How to set up? fireware latest issued on18th/june. I did some search on this forum, but couldn’t figure out how to do. Thank you for any help....
View ArticlePan Servo acting strange
@RizHass wrote: I have servo-driven Pan and Tilt gimbal on a plane, and in order to slow down the movement of my servo, I have my TX16 set as 3.0Sec slow down in both directions (up and down) set....
View ArticlePitch up_down behavior during and immediately after transition
@Sandpiper wrote: I have flown my quadplane about four times, three of them being autonomous transitions. During forward transition the quadplane usually pitches up/down as it gains/loses, flies what...
View ArticleESC and motor working only once connected to PC via USB
@Maciek_S wrote: Hey, I am making a new setup with a new plane. I reflashed my Matek H743 - it happens the same thing with both arduplane 4.0.8 and 4.1. I configured that via MissionPlanner (ranges,...
View ArticleRTL Crash using 4.1.0 beta1
@softboy wrote: Hello everyone… I’ve setup an AR Wing Pro with Pixhawk1, using TBS Crossfire for RC, M8N gps and compass and loaded it with 4.1.0beta1. Did all the calibration procedures, like accel,...
View Articlesafe flight on a mission
@Brigambyli wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleAirspeed arspd_autocal making VTOL stabilized modes unstable
@Sandpiper wrote: I recently attempted to start tuning my quadplane. The first step was to calibrate the airspeed sensor. So I enabled arspd_autocal parameter and started my auto mission. During...
View ArticleCould not land! Forced crash as I fought for control over continuous auto...
@Cam3n wrote: I’ll start this post by saying I did, for the first time, intentionally set the BATT_FS_LOW_ACT to 1:RTL prior to flight (hey it sounds perfectly prudent until you keep reading). Also,...
View ArticleNo channel 4 and 5 output, possible BRD_SAFETY_MASK bug?
@Supermagnum wrote: Hello, I cannot get any movement on channel 5 and 4, even if channel 1,2,4 and 5 even if these are set in BRD_SAFETY_MASK. channel 1= rudder channel 2= elevator channel 3= throttle...
View ArticleClik here to view.
SITL Linux Set-up Troubleshooting: Error in the AP_BattMonitor_logging.cpp?
@CAPTA1NHERPDERP wrote: Hi There, I am new to ArduPilot and I have been trying to setup the SITL simulation environment. What I have done so far (following the instructions on setting up the build...
View ArticleManually Test Servos by Mission Planner only without Transmitter?
@BeanHat wrote: how can you manually move the servos from the mission planner? my servo is connected to the cube rail and getting powered by a separate 5V output. I cant seem to find the tab where you...
View ArticleSonar not used with Vtol plane (AP 4.0.9)
@Lorenzo_Pessah wrote: Hi all, I just installed a analogue sonar on my Vtol plane. (tricopter, 2 tilting motors). Sonar is correctly read by the system when disarmed, I checked this with mission...
View ArticleVTOL slows down when it is flying in auto mode
@jimmy_pinedos wrote: Hi everyone, I have some troubles with VTOL drone built with ardupilot. It is working relatively good, but sometimes when it is fliying in plane mode in an auto mission, turns...
View Article[Solved]Plane 4.1 Stabilize mode, Elevator goes down instead of up
@Elka wrote: Pixhawk 2.4.8, Plane 4.1 dev. Accel calibration successful for all axises. Auto-tune not performed yet (did not fly yet). Plane: 2.4M foamie glider. During control surfaces response check...
View Article