Clik here to view.
Error starting simulation in mission planner
@andyp wrote: Hi. Following this guide https://ardupilot.org/dev/docs/sitl-with-realflight.html After selecting flightaxis, when I click on one of the aircraft type icons it says ‘downloading sitl...
View ArticlePlaying back a real dataflash .bin in SITL, visualised with RealFlight
@andyp wrote: Hi Is it possible to play back a ‘real’ dataflash .bin file of a flight (say using SITL) to RealFlight sim to visualise a flight? I guess the plane on RealFlight just follows SITL...
View ArticleClik here to view.
Copter Works, Quadplane Doesn't (Solved)
@Brodo wrote: Hi friends. I’m trying my first quadplane build. Since I’ve been expecting trouble I am testing the copter components on a piece of timber the same weight as the plane fuselage while the...
View ArticlePixhawk motor and control surface servo connection
@Prathamesh_Patyeker wrote: hi guys need some help , I’m new pixhawk so need a small help , can you tell me where to connect motors and servo pin on output side , i have attached my parameter file if...
View ArticleOctoQuadPlane VTOL motors freewheeling - ESC Brake option
@TTGold wrote: I have finished my latest OctoQuadPlane Build and it now finally flies very well. I have one problem where at times the top front rotors will freewheel in climbs, turns, and in windy...
View ArticleAutotune Zeta WingWing Z84
@Matthias_Hryniszak wrote: Hello, I am trying to autotune my long-range Z84. I started with a quite low AUTOTUNE_LEVEL of 6, but it resulted in the plane getting vertical oscillations. So I thought...
View ArticleOld APM 2.x FW3.4.0
@Gert_Fourie wrote: A very good day to everyone, What an awesome community. I have been using the www and related since I bought my FC. I got my, then, brand new APM 2 FC as soon as it became...
View ArticleDuane's Fighter VTOL 4+1 Build Questions and Notes
@ddegn wrote: I’ve been reading with interest the Fighter VTOL 4+1 thread. After seeing the crazy high shipping prices to purchase this aircraft from AliExpress, I decided I’d but it from Banggood...
View ArticleCan somebody please check my parameter file?
@Supermagnum wrote: Arduplane V4.0.9 channel 1= rudder channel 2= elevator channel 3= throttle channel4= flaps channel5= balance rudders ( ailerons) channel 8 = flight modes All channels exept 3...
View ArticleClik here to view.
Out of control roll: Looking for crash/log analysis help
@David82 wrote: I had a few successful flights while using autotune, stabilize, cruise, loiter and RTL modes. (I read the wiki on autotune and was doing many hard banks and hard elevator changes to...
View ArticleMagnetic heading shown in on-board display
@Willflyformoney wrote: Greetings, has anyone been successful in displaying anything other than the stock information on the onboard display? I have a need to show the magnetic heading on the small...
View ArticlePlane 4.1.0 Beta PID's
@Unmannedservices wrote: Hi, I’ve upgraded my firmware on my Pixhawk to 4.1.0 Beta which is in an AR wing. I flew in auto tune but I was not happy with the results and want to revert to my old PIDS....
View ArticleError building firmware - WSL2
@andyp wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Questions about Q_frame_class parameters
@xingxing wrote: Hi,I try to lean VOTL ,So I buy a nimbus 1800 VOTL which is produced by Kris.I found the Q_frame_class=1(Quar) and Q_frame_type=1(X type),but the nimbus 1800 VOTL only have three...
View ArticleAutomatic Arming
@Giorgo wrote: Hello developers, please, would it be possible to add an option for automatic arming, as soon as all Pre-arm safety checks are OK? I done already two take-offs from hand without arming...
View ArticleActivating NMEA output on serial port
@andyp wrote: Using an OmniBusF4. I think NMEA output from a serial port is not available because the firmware is ‘limited’ on 1mb boards....
View ArticleSmart audio switch and Logic setting
@xixijoe wrote: Matek_F405wing, rushtank+VTX. I tried to get 3 shift of power set with 25mw,200mw,800mw.by assign one switch from 200mw to 800mw and together with arming activate to 200mw. here is my...
View ArticleBad GPS health and bad gyro health
@xixijoe wrote: matek405wing. with latest firmware at 18/june,2021. I can arm my plane with 15 sat above, but. It keep telling me bad GPS and bad gyro health. Posts: 9 Participants: 2 Read full topic
View Article! Crashed ! Analysis Please
@kerrycorcoran wrote: MFE Believer Matek F765 Wing Flight Controller Arduplane 4.1.0 (dev) Had been flying the aircraft since the start of summer with no issues; airframe had approximately 15 or so...
View Article[Solved] PIDs not displaying
@darrell wrote: I’m not sure if this is a 4.1 beta issue or a Mission Planner issue but the roll and pitch PIDs are not displaying in Mission Planner. Here’s a log of a flight I did today. There’s a...
View Article