Clik here to view.
Autotune not work with too rapid movements
@Alexey_Degterev wrote: Hi! Last day i try to autotune my small plane dart 250g. I set AUTOTUNE_LEVEL to 7 in firs flight and 8 in second. In previous autotune session i probably move stick too lazy...
View ArticleClik here to view.
SERVO_AUTO_TRIM probably not update trims
@Alexey_Degterev wrote: Hi. My plane have SERVO_AUTO_TRIM=1 always enabled. after first flights i have this trims. The elevons with these trims in the manual are raised equally upward by 2-3 mm...
View ArticleClik here to view.
VTOL Nutball Quadplane
@flyingw wrote: The Nutball is an unusual subject for a quadplane in that the fans can be mounted within the shape of the airframe. I test flew the plane just to see if it would still fly after...
View ArticleKind of a high level question but... why does one of the most expensive FCs...
@MrDysprosium wrote: When I first started my FPV/Long Range adventures, my friends convinced me to purchase the best options first, to not risk something stupid happening because of cheap hardware....
View ArticleCustom mavlink message
@Ador_Dastan wrote: Hello everyone, I’m using ArduPlane4.0.3 to create a mavlink message, I’ve added CUSTOM_MSG in ardupilotmega.xlm and compiled with ./waf configure && ./waf plane to get the...
View ArticleIntercepting Radio Channel Values
@cbrviking wrote: I want to intercept the value sent from the radio through the PX4 Cube to a servo. I have successfully intercepted the output from an autopilot command but not one coming up the...
View ArticleCompensated vario total energu
@adcam wrote: hi I understand that arduplane could provide through TECS an equivalent of total energy variometer. I read through the doc...
View ArticleQuestions on Autotune
@eminakgn wrote: Hi everyone, AFAIK ArduCopter can tune PIDs autonomously. Do you think that it will be feasible to design such autonomous autotune process in ArduPlane? Once we know the enviroment,...
View ArticleVTOL motor stops when yaw
@Sarunas_Budrevicius wrote: Hello, I have an issue with VTOL, when I am trying to fly in QSTABILIZE mode all motors spins fine it flies normally, I can do roll and pitch movements but when I try to...
View ArticleQuadplane Flaps support
@Zadrob wrote: Hello, has anyone tried flaps support in Quadplane? I have built Nimbus VTOL with extended wings, with separated flaps and ailerons on each wing. I wanted flaps functionality in...
View ArticleOmnibus f4 V5 receiver issue
@Dave_S1 wrote: I have an Omnibus f4 v5 and want to use ardupilot to experiment with mapping. Im having an issue getting my Spektrum receiver to connect with the Omnibus. I am binded to the receiver...
View ArticleAutotune P gain anomaly
@eminakgn wrote: Hello, here is the flashlogs of the flight that I tried to perform Autotune. Can someone help me analyze my autotune results before going for a full AUTO flight. The change in P gain...
View ArticleForce SRTM *.dat on the SD card
@bendead wrote: Hi, I would like to upload an entire country SRTM data to my SD card, It will only weight about 40-50 MB total, but every time I am doing a flight plan with all the country, with...
View ArticleClik here to view.
Bixler QuadPlane Crash after Perfect Transition to FBWA Mode
@dbaldwin wrote: Hi, I’m wondering if I can get some assistance diagnosing a QuadPlane crash yesterday morning. I’ve done several hovers and everything worked flawlessly with the forward transition. I...
View ArticleSet Home Position on First Arm Only
@vantasstic wrote: So one day I’m flying my plane, miles out, and went to change flight modes and, instead, moved my ARMing switch and disarmed in flight. No biggy, I just lowered the throttle, moved...
View ArticleClik here to view.
20-Foot Wingspan Quadplane -- Successful First Flight!
@Illini_Rob wrote: After months of prep, I finally got the old Gooney Bird in the air! Blog entry here: Gooney Bird Drone Latest News On Monday, June 8, I drove seven hours to the Alvord Desert in SE...
View ArticleMission download timeout with Dronekit-Python
@eminakgn wrote: I am having timeout issiues with dronekit. Here is the related issue on github. Are there known issues or any incompatibility with mission protocol in Plane 3.9? Posts: 1...
View ArticleClik here to view.
BAYQUS-Completely 3d printed eVTOL drone
@Artem_Skorsky wrote: I just wanted to share my VTOL project. Purpose is to desing very easy to manufacture VTOL drone ( completely 3D printed). Here are some pictures from first prototype On Wing i...
View ArticleFlap and Motor outputs not working
@svede wrote: In the Setup tab under Servo Output for configuring a new plane the motor and flap sliders indicate they are not outputing the signal from the radio. The radio configuration went fine,...
View ArticleStorm32 gimbal with plane
@Autonomost wrote: Hi All, Does anyone know if the storm32 boards will work with plane4.0+? I have configured it according to the documentation but I still cannot get the gimbal to react to mavlink...
View Article