How to add more motors in the configuration code?
@dodobird wrote: Hi guys, I’m a new developer trying to use ArduPlane for an aircraft that has 4 motors on each wing, similar to the NASA X57, and I’m unsure what the best way to add more motors to...
View ArticleClik here to view.
3D Printed VTOL in the works
@quadsours wrote: Heres my 3d Printed VTOL-fw I have most of the work finished but noticed the 9" props are not able to cut the mustard. I did get it air born but it not happy. 12244577-a1280×720 427...
View ArticleRegarding plane
@quadsours wrote: Hello, I have a few questions after programming a VTOL. Motors do not disarm even after a crash I have to use Radio. flight mode does not beep when engaged. Motors seem under...
View ArticleWhere in dataflash can I see throttle demand while in VTOL mode?
@Andre-K wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleExporting CAN information to external program
@Alex464 wrote: I’m fairly new to the pixhawk and mission planner itself so I apologize if this has already been asked and answered or if I’m simply missing the documentation. Currently I am trying to...
View ArticleScope and Syntax of SITL Instructions among ArduPlane, Jsbsim, Flightgear
@Albcem wrote: Could someone be kind enough to explain how ArduPlane, Jsbsim and Flightgear interact in a SITL simulation? Is MavLink the only outbound and inbound instruction language for ArduPlane?...
View ArticleClik here to view.
Crash cause: perhaps due to loose battery?
@Sunny52266 wrote: Hi, I had a crash today. Attached is the log file and a screenshot of the flight data. Annotation 2020-06-16 1205191704×585 199 KB The only reason I can come up with is that the...
View ArticleVTOL Position and Velocity control
@Rui_Loureiro wrote: Hello all, Currently im testing a VTOL integration on mavros using a custom version of gazebo that supports Ardupilot quadplane. Could anyone tell me if the Position control and...
View ArticleController/Servo Movement Issue!
@Anna.Fisker wrote: Hi I’m Anna! I am new to the world of Ardupilot and I am having some issues getting my servos to respond to my controller. I have my pixhawk 4 set up for a fixed wing plane and...
View ArticleServos working, no throttle
@Brend.an wrote: Hi. I have a matek f405 in an AR wing. I can control the elevon servos from my radiomaster tx16s and the radio calibration functions properly. However under the servo output tab there...
View ArticleFixed wing turbine Setup
@flite_x wrote: Hi Guys I am fairly new to this forum, but it’s awesome to have a place to discuss different topics. I have been experimenting with the Pixhawk Cube for the past few months on a 50 CC...
View ArticleESC question - strange beeps
@anparkinson wrote: I replaced my dead 3536 1400kv motor with a 3536 1450 kv motor, different brand. After arming the Pixhawk the ESC beeps twice repeatedly after giving the motor full throttle, but...
View ArticleHow to tune ground steering
@xingxing wrote: hi guys ,my RC plane was flight good except ground steering ,the plane was installed F405 WING which was flushed arduplane fimware 4.0.5,I have check the wiki of ground steering many...
View ArticleHow to read analog data for other temperature sense on ADC pin? (pixhawk 2.1...
@omer_ali_erdemir wrote: Hello everyone!. I tried to read analog data on ADC pin for temperature sense. I followed the steps on this site one by one:...
View ArticleAirspeed sensor and Omnibus F4 pro FC
@martinlta wrote: Hi How do you connect ( what pin etc) a anolouge airspeed sensor to the omnibus f4 pro running with arduplane. Posts: 2 Participants: 2 Read full topic
View ArticleCan not build arduplane for f303-Universal board
@Romanik wrote: Hello friends I am trying to build arduplane target for f303-Universal board cause I have a lot of SP racing F3 flight controllers . I am aware this controller listed as unsupported ,...
View ArticleAdding new channels to Rascal for SITL with Jsbsim
@Albcem wrote: Does anyone know how I can add new channels to the Rascal Jsbsim model? Currently it looks limited to 4 channels on ArduPlane. Thanks Posts: 1 Participants: 1 Read full topic
View ArticleHow to display the temperature of gas engine in mission planner?
@Sarunas_Budrevicius wrote: Hello, I have Arduino with temperature sensor for my gas engine to know the temperature but I need to have this information in mission planner. Does anyone know how to set...
View ArticleArduplane soar/gliding?
@ohitstarik wrote: Hey, I’m trying to soar with arduplane on an aircraft with no motor (glider). I’ve set SOAR_ALT_MIN to 0, and soar vertical speed to 10 m/s. soar max alt to something ridiculous....
View ArticleClik here to view.
Altitude reset in flight
@rx-midget wrote: I need some help from the group. I’ve been using Arduplane for some time but this issue is beyond my knowledge level. I was just out flying my F405-Wing with Arduplane 4.0.5 and had...
View Article