Clik here to view.
Interesting flight behavior at a Rally Point after RTL
@flyingw wrote: I had a successful test flight on Sunday with ArduPlane 3.7 on a Navio2 with four waypoints and a rally point in the middle. After the last waypoint it went towards the Rally Point and...
View ArticleBest low cost Pixhawk/PX4 clone
@ypsonar wrote: Dear Friends,Please suggest good low cost Pixhawk / PX4 clone, there are numbers of Chinese pixhawk available but in that which best please suggest, please suggest some good brand...
View ArticleDifferent controllers?
@skypuppy1 wrote: I've loaded the control software for the hexacopter and on that I'm using a PixHawk 2.1 Cube. If I want to use ArduPlane on a plane, do I have my choice of the 2.1 Cube, an...
View ArticlePlane loosing ALT and crash
@ILAP1 wrote: Arduplane ver. 3.7.1 on Pixhawk 1Plane: Ritewing DRAKDescription: Auto takeoff with bungee, auto mission at 100m alt - all went well.Then when switched to RTL at the end of the mission...
View ArticleClik here to view.
Plane dive to ground when switch to FBW and AUTO
@ILAP1 wrote: Arduplane version: 3.7.1Plane: Ritewing DRAKDescription: Auto takeoff into AUTO mission at 100m ALT. Mission completed successfully.At the end of the mission mode changed to RTL - at...
View ArticleClik here to view.
Question for Dr. Tridge
@Shane_R wrote: Firstly I would like preface. Although we have been working on this project for almost 2 years another person has been doing the test flying thus far. I just got my test plane together...
View ArticleReading the PWM value for the throttle
@Tryggvi wrote: Hi Where from the dataflash log can I find the PWM value the pixhawk is sending to the ESC? In the CTUN I can find the ThrOut but those values are between 0 and 100 in one of my logs....
View ArticleWhere do I tell the Navio2 that it is receiving SBUS or PPM?
@flyingw wrote: I cannot locate any such parameter in the parameter list. Does it have to be set to either PPM or SBUS? Thanks, Paul Posts: 1 Participants: 1 Read full topic
View ArticleFly Away with Arduplane 3.7.1
@juvinski wrote: Hi guys, If someone could help I will appreciate. I fly a mission today and excepting the landing everything was ok.So I changed the landing trying to see what could happen, but after...
View ArticleV-tail with split control surfaces
@fabianr wrote: Hey Ardupilot-Community! On a v-tail I have split control surfaces on each side, so four in total. The two servos on each side are mounted opposite each other, so they require reversed...
View ArticleClik here to view.
Altitude (pitch) correction too hard, what to tweak?
@lanzo wrote: I use My Fly Dream Twin for a while and it flies very well, the only thing I notice is that corrects altitude too violently, using too much pitch to go down then a lot of motor to gain...
View ArticleBad Logs errors
@yak-54 wrote: Hi i though i give 3.8 a go with new pixhawk 2.1 when i try to arm it i get bad logging error in mission planer so i tried to turn off all loging still the same cant arm the plane...
View ArticleAPM 2.8 can fly QuadPlane
@ypsonar wrote: Please guide, Can we fly QuadPlane with APM 2.8 board with Mission Planner firmware 3.2.1Documents says that APM 2.8 no longer support with latest firmware.Please guide Posts: 2...
View ArticleReverse Servo - Manual Mode
@Andy_M wrote: Hi Guys, Is there a method to reverse a servo for manual mode in arduplane without using the transmitter? Ideally I'd like all mixing to be done on the board (rpi + navio2). There...
View ArticlePower reduced to idle to make descents while in AUTO
@flyingw wrote: When I pass through a waypoint and the next waypoint it is a lower altitude, the autopilot reduces the power to almost off until the target altitude is reached. Then it throttles back...
View ArticleSuper Huge Mugin with Pixhawk
@albert wrote: Hi Has any one used a pixhawk in a Super Huge Mugin? I have some intitial gain values, but would a appreciate any setup suggestions. Thanks Posts: 2 Participants: 2 Read full topic
View ArticleAfter takeoff airplane turns and starting to decend on Auto mode,,, it...
@Artem_Skorsky wrote: Hi,I set mission, it takes off on automission, then turns direction to waypoint but decending , when it is close to ground i switched to FBWA and took the control,, but it...
View ArticlePixfalcon reboots in flight
@JakobThrane wrote: log_18_2017-7-31-17-07-44.bin (444 KB)My Pixfalcon reboots in flight. I lost control yesterday. Luckily the plane, Bixeler 3, went slowly down into a field without damage. I´ve...
View ArticleGeotagging NIR Images from Pixhawk & Mission Planner
@pds66 wrote: Can anyone show me how to georeference my images? I have a pixhawk that unfortunately is situated in a skywalker platform that cannot be moved, so I believe I can get the file from...
View ArticleTrigger Camera Now not working on ArduPlane 3.7.1
@RodrigoMeirelles wrote: Hey guys, I have a problem with the camera shot on Mission Planner. I'm using Pixhawk 2 The Cube with ArduPlane 3.7.1, and with all parameters set correctly, my IR trigger...
View Article