Clik here to view.
Quadplane QTUN.DAlt not tracking CMD.Alt
@phinchey wrote: I’ve just started my first few test missions of my new quadplane, and it’s losing altitude throughout the mission until it touches down. It takes of to the right altitude, but...
View ArticleClik here to view.
Cause of potential brownout and loss of logs?
@justinjmatt wrote: Recently I had a flight where all logs were lost after about 1000s of log time. I’ve done some investigating and I am currently trying to reproduce the issue. I am running a...
View ArticleQuadplane Slowly flipping over in QSTABILIZE
@Warrono wrote: Trying to takeoff in QSTABILIZE mode with my quadplane, but each time it flips over depending on the initial tilt. So I’m thinking that the auto-correction may be backwards because of...
View ArticleMission autoLAND hard rudder near gnd
@1Gump wrote: Flight Log . cuav V5 4.0.7 lidarlite v3hp (i2c) airspeed sensor glow fuel engine. . this happens consistently and repeatedly (every time) except that the direction of the rudder changes...
View ArticleClik here to view.
Pixhawk Cube ads-b on Flightradar24
@prodha wrote: I am using Pixhawk cube. there is a built-in ads-b receiver. but there is no transmitter. how do i set up an ads-b transmitter ? What should I do to see my own plane on the...
View ArticleVTOL Compass Issues
@Tom_Simmons wrote: Hi all, I have a question about some compass issues that we are experiencing with the Foxtech GreatShark VTOL 330. This VTOL system is running the CUBEorange and the HERE+ GNSS...
View ArticleOctoquad Plane log shows hover Throttle below 50% but pwm in hover is well...
@TTGold wrote: This is my first Octoquad build in H config and was trying to figure out if I estimated the power in my motors/props correctly. When I look a the logs in Hover I noticed that it hovers...
View ArticleNewbie with an FC-10 DOF
@fastatstandstill wrote: Hello all, I’m new here and new to Ardupilot. I’ve been flying my current Drift on INAV, but wanted to try AP. I have an AR900 wing pro and fitted an FC-10 DOF to it. I’m...
View ArticleClik here to view.
SmartAudio - wrong frequency - only one power level
@Target0815 wrote: Firmware: latest DEV version Band / channel selection set in the VTX* parameters is not taken over correctly. Band 3 (Airwave) and channel 3 should result in 5800 MHz. This is also...
View ArticleBicopter tiltwing
@alessandro_giovanard wrote: Hi, I’m starting to build a bicopter, BUT, I’ve seen some v-22like frames, some tail sitters, but no both at the same time. The classic bicopter tiltrotor has a big...
View ArticleClik here to view.
Arduplane 4.0.9 dives in Auto modes
@mgrimes1907 wrote: I have two large mapping frames that have Black Cubes in them. They both were running 3.9 firmware and flying well. I completely erased both and installed the Rover firmware to get...
View ArticleSITL & MAVproxy (for ArduPlane) doesn't make it to command input
@FullyPositronic wrote: Hi folks, I’m posting a question here because I can’t find the answer anywhere else (checked the the forum, Reddit, github etc.) but if it’s been asked before, just point me...
View ArticleFailed to connect to SITL instance error
@viper16 wrote: Hi everyone, When I try to connect missionplanner with xplane, I get the error “Failed to connect to SITL instance”. When I connected yesterday there was no problem but today I have...
View ArticleWhat is the principle of this autotune process?
@dexin_sun wrote: Is there any theory or literature that can be referred to; I don’t understand the meaning of ‘bounce back’. I can’t understand the adjustment principle of D value Posts: 2...
View ArticleAborted landing and flaps
@1Gump wrote: Ive noticed a behavior, on aborted landings, that retracts the flaps immediately when the abort command is given - at least when the abort comes from a manual (rc input) mode change. ill...
View ArticleAdding folders in other ways
@Kungsfiskare wrote: Hey community. I’m trying to run a autostart script for auto mode. For some reason I can’t add a folder to my 3DR pixhawk mini to do scripting. Is there any way to add folders...
View ArticleClik here to view.
Problems with vectored yaw stability for different motors
@gunnir wrote: Hey everyone, I’m in the progress of designing a new quadplane which will utilise 4 motors. Two wing mounted motors tilt (vectored), and two fuselage (nose and tail) mounted motors...
View ArticleClik here to view.
Tricopter VTOL back-flipping late in Hover->Forward Transition
@StephenCarlson wrote: image1426×439 63.7 KB I have my vehicle flying well in FBWA, and QLOITER, QHOVER and QSTABILIZE. I’ve been launching the aircraft by hand in forward-flight mode in order to get...
View ArticleCustom Field value always 0
@grzesiar wrote: Hi all I’m stuck at one little issue. According to: https://github.com/ArduPilot/MissionPlanner/pull/2360 It is possible (and should be quite easy) to display NAMED_VALUE_FLOAT in...
View ArticleSetup arduplane in gazebo / ubuntu 18.04
@Elif_Senturk wrote: I search too much about plane for simulation. I could not open the simulation with plane sim. How can i use plane instead of copter? Posts: 1 Participants: 1 Read full topic
View Article