F.port setup on Pixhawk
@RizHass wrote: I have a R9 mini RX with F.port FW flashed. How do I connect my receiver to a Pixhawk serial port? I cannot find and wiring diagram specific to Pixhawk. On Pixhawk, ground and power...
View ArticleExternal Barometer to be primary
@eminakgn wrote: Hello everyone, I have managed to enable barometer in Here 2 GPS module through UAVCAN and I have realized that scaled_pressure messages are being displayed in MAVLink Inspector in...
View ArticleCan we change q tilt mask with an aux switch in vtol?
@Ravi_K wrote: I am just thing why to waste battery when there is no extra payload in vtol plane mode.by going to all vtol doc I found that Couse of motors to tilt is q tilt mask.if we can access it q...
View ArticleGuided Mode - Help with Q_GUIDED_MODE transition
@Leon_Fargher wrote: Hi all, I am flying a quadplane in guided mode using a dronekit application that updates the target position to fly in smooth circuits. I have Q_GUIDED_MODE enabled so that when...
View ArticleThrust to weight ratio
@TheGS wrote: hi; I am building a 10kg electric VTOL UAV; I know the ideal t/w for VTOL motors is 2:1 or 3:1 but I don’t know the ideal ratio for propulsion motor. can anyone help me? Posts: 8...
View ArticleA Query About Rudder Mixing
@Taipan wrote: In the wiki section on FBWA Mode, it says in part: In FBWA mode the rudder is under both manual control, plus whatever rudder mixing for roll you have configured. Thus you can use the...
View ArticleHardware in the loop simulation with 4.0.5
@ColonelChicken wrote: I am trying to use HIL to simulate ArduPlane on a pixhawk cube using Q ground control as my GCS. I am running the latest ArduPlane (4.0.5) and I have heard that HIL has not...
View ArticleAnalog Air Speed Sensor
@iSkyMaster wrote: I am off to learn what the fuss is all about Air Speed Sensors, so I bought few analog ones (as I want to save my I2C), and connected to Pixhawk via ADC port. As per Ardupilot...
View ArticleHow to loiter without Power (gliding in termic)
@mogli73 wrote: Hello! How can I disable the altidude-hold-mode in loiter-mode? I have set the SERVO_3FUNCTION from Throttle to RCPassThru because I like to circling in the termic without Power. How...
View ArticleThrottle spikes while loiter, and make plane stall
@Hadits_Baroya wrote: Hi All, What can cause throttle spikes in a plane? So I was doing a mapping project, everything was fine when the plane doing automatic waypoint and Return to Launch. After the...
View ArticleV Tail setup with F405 wing
@DanWA wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleFilght mode and HIL mode
@AhmadAdel wrote: Where can I find Normal flight mode C code for apm 2 ? Hardware in the loop C code for apm 2 ? Normal flight mode C code for PIXHAWK 4 ? Hardware in the loop C code for PIXHAWK 4?...
View ArticleSetting up Beaglebone Blue with TFMini Serial lidar
@sdeal3 wrote: Hello all, I am setting up a Beaglebone Blue with the latest Plane 4.0 and I have been struggling to get the TFmini lidar to work with it. The details of the setup, I have the lidar...
View ArticleZohd dart 250g maiden
@TheTroll wrote: Just flown with my Zohd dart 250g. Actually it wasn’t 250 but 265… Anyway, there is a video of first fly Posts: 3 Participants: 2 Read full topic
View ArticleNeed a generic advice on the wind sensor
@Paul_Atkin1 wrote: Hi, need an advice - my son got me into a new build - SonicModell Binary RC 1200mm. I never built planes, only copters before. I will use Kakute F7, have probably more than enough...
View ArticleTwo bad crashes in VTOL automission
@Kaveh wrote: Hello friends. I have tuned and flown many VTOL drones. The main way I fly the drones is to take off vertically in QLOITER mode and transition to fixedwing flight by changing the flight...
View ArticleTesting 4G connection for suitablility
@JCWag wrote: Hi, I would like to test our 4G network in the area for suitability for flying drones with UAVcast. Using just a RPi3 and a 4G dongle what would be the best method to test the network...
View ArticleMission planner / bluetooth connection
@pkweagle wrote: Looking for assistance with Mission Planner w/ Dragonlink TX/RX and Bluetooth connection. Mission planner fails to make a complete connection. After weeks of alternate equipment...
View ArticleDronekit doesn't work with CubePilot orange with the ADS-B feature
@ohitstarik wrote: Hey, So I recently started having exception in message handler problems with dronekit when i transitioned from a Pixhawk 2.4.8 to a Cubepilot Orange. I solved the problem and...
View ArticlePlease take a look onto crash logs
@TheTroll wrote: Hello! It was a sudden crash without a reason. Fortunately vehicle was found undamaged. Bud tge reasons of crash still not clear. It would be really nice if someone take a look onto...
View Article