Clik here to view.
Xplane data in and out setting change automaticly when I run sim_vehicle.py...
@Brian_Duvall wrote: Hello everyone, My problem is when I run x-plane then run sim_vehicle I am getting a bad AHRS. When arming the throttle I get 3d accel calibration needed. I cant see to find the...
View ArticleAuto tune tilt-rotor in forward flight
@hybrid-guy wrote: Hey everyone! Can I run an auto tune in forward flight after I transition into cruise? The vehicle flies ok in forward flight but I want to get it better! Should I use the following...
View ArticleRandom servo movement Q-plane
@Roby wrote: Hi. I have random servo movement in all guided modes (FBWA, Qstabilize, …) manual work fine. PH 2.1 Cube (FW 3.9.4; also tried on 3.9.3) High performance Futaba servos (BLS 177 SV) Servos...
View ArticleNimbus Tricopter Front Motors not Vectoring
@Hein_Du_Plessis wrote: Q_FRAME_CLASS = 7 Q_FRAME_CLASS = 1 Q_TILT_MASK = 3 Q_TILT_TYPE = 2 My front motors pitch up in q_stabilize, but do not vector as I bank the plane. I can hear the motors spin...
View ArticleClik here to view.
How to configure radio in Revo board running Arduplane
@wcfung1 wrote: I just flashed Arduplane firmware V3.9.4 into an OpenPilot Revolution board using iNAV configurator in Google Chrome. Gyro works as seen in HUD of MP. However when I do radio...
View ArticleClik here to view.
Boing314 JSBSim Sitl linux? I got the Rascal to simulate in JSBSim ardupilot...
@josheeg wrote: Boing314 JSBSim Sitl linux? I got the Rascal to simulate in JSBSim ardupilot since new documentation came out. So I coppied Boing314 into the folder Rascal’s folder is in. Then in that...
View ArticleVTOL quadplane SITL with designs going to JSBSim would be efficient
@josheeg wrote: VTOL quadplane SITL with designs going to JSBSim would be efficient. With the new JSBSim information in the SITL linux tutorial I got the Rascal to simulate I have not gotten the...
View ArticleArduplane 3.8 sucks!
@greystone wrote: I have tried and tried to get elevons working on my new pixhawk mini (3 days). I have read all of the documentation but no joy no matter what. Why did they have to fix something that...
View ArticleBattery monitor can´t configure 3.9.4
@ginodouglas wrote: When I tried to configure the battery monitor in a plane 3.9.4 I got the message “This feature is not enabled in your firmware”. I am using a HKPilot and a battery monitor both...
View ArticleSmart RTL for planes
@TonyRe wrote: Is Smart RTL also available in ArduPlane? Posts: 2 Participants: 2 Read full topic
View ArticleNo UAVCAN under Pixhawk 4
@RoverHunter wrote: Hello all. I have one Holybro Pixhawk 4 board where the two UAVCAN bus connectors are not working when running ArduPlane v3.9.4. I have set the two drivers parameters has shown...
View ArticleHow to flare smooth just with barometer
@xingxing wrote: hi guys, my skysuffer X8 land a little bit hard in auto land，it seems can’t hold the ALT when the flare triggered. I have read the manual twice, but it’s no much clear i think. any...
View ArticleQAUTOTUNE for VTOLs
@GregCovey wrote: This looks interesting for VTOLers. It’s still in beta but looks simple enough to try for those that are looking for some tuning help. You can set it up to tune only 1 axis at a...
View ArticleClik here to view.
Airspeed problem
@PIXMAV wrote: I am using plane3.8.5, after calibrating the sensor, I have used the MS4525 airspeed sensor. I have not taken off yet. I found that the airspeed value displayed on the ground station...
View ArticleClik here to view.
XPlane 10-11 The plane’s not responding
@Enes_Baspinar wrote: Hello my friends and sir @Michael_Oborne(thanks for the program). Firstly I am sorry for my English I want to fly the plane in XPlane10 or XPlane11 with the Fight Plan in Mission...
View ArticleClik here to view.
MS5525 sensors from MRobotics
@ardisd wrote: I have an MRobotics MS5525 Airspeed Sensor on my quadplane and in the last few flights I have had problems in getting the plane to disarm. I think the problem is the Airspeed sensor not...
View ArticleClik here to view.
Kdiff3 compare JSBSim output of Rascal and Boeing314 jsbsim example aircraft...
@josheeg wrote: I used ctrl + Middle Mouse Button to pull up the menu of xterm and stop the screen scroll to debug the differences of Rascal running in JSBSim vs another JSBSim aircraft Boeing314 has...
View ArticleQ_VFWD_ALT: Forward velocity alt cutoff units
@Chad_Frazer wrote: range for this parameter is 1-10, can anyone confirm if the units are meters, cm, feet or AU’s?...
View ArticleF4 Omnibus Pro Roll is mirrored on HUD
@Alexander_Perez wrote: I just installed the arduplane firmware as instructed on the ardupilot website (http://ardupilot.org/plane/docs/common-omnibusf4pro.html) using the F4 Omnibus Pro board. To...
View ArticleVTOL navigation goofiness
@jace26 wrote: We’ve been using 3.8.5 for some time and have always had issues with VTOL navigation, including it resulting in some wrecks due to odd behavior. We are considering moving up to 3.9.4...
View Article