Plane dives at full power when switched to Auto
@RANND wrote: This is an Omnibus F4 Pro config, running Plane 3.10.0-dev in a Skyhunter. I maidened the plane in Manual and added a couple of clicks of elevator trim for level flight. I then used...
View ArticleClik here to view.
Controlling a Gimbal Via Pixhawk Cube
@Montville wrote: Hello, I have purchased this camera/gimbal Yangda Security Sky Eye-I 1080P 10X Zoom Camera For Drone 1080P 10X Zoom Camera | 3-Axis High Stabilized Gimbal System | High Quality...
View ArticleClik here to view.
I am trying different aircraft downloaded from JSBSim and unziped aircraft...
@josheeg wrote: I am trying different aircraft downloaded from JSBSim and unziped aircraft folder contents to aircraft folder as the rascal in SITL rather than Rascal they are not working. Started...
View ArticleI am simulating the Rascal and it overloads the -l CMAC other locations load...
@josheeg wrote: I am simulating the Rascal and it overloads the -l CMAC other locations load it doent run a mission the alt is below the ground. Terain check MANUAL> TERRAIN_REPORT {lat :...
View ArticleSome GNSS questions
@Roby wrote: I run 3.8.5 software for VTOL quad-plane and I want to know some things because in the manual does not say much: what will happen if GPS is jammed while in the air in forward flight? what...
View ArticleTwo Aileron Channels and broken link
@CaptainCanyon wrote: I’ve read responses to similar posts, but still haven seen what I’m looking for…. I have right and left Aileron servos and right and left Flap servos on my model. I’ve configured...
View ArticleNimbus VTOL Throttle mid settings
@Liquidforce wrote: Hi Guys, I hope I am asking in the correct place for this. I am having a problem with my Nimbus VTOL. I have built it myself and am at the point that I can hover in Q Stablize,...
View ArticleClik here to view.
JSBSim does not seem to work It won't load location CMAC but will load others
@josheeg wrote: JSBSim does not seem to work when I try to run the first plane mission mentioned in http://ardupilot.org/dev/docs/plane-sitlmavproxy-tutorial.html#plane-sitlmavproxy-tutorial I load...
View ArticleClik here to view.
Tilting motor servos
@hybrid-guy wrote: Hey everyone! I am curious to what are high end servos that allow for tilting some bigger motor and props than the nimbus vtol. I am using the 3115mg on my nimbus and they don’t...
View ArticleClik here to view.
Plane 3.9.4 stable release
@tridge wrote: ArduPilotPlane.jpg750x291 33.1 KB The ArduPilot development team is delighted to announce the release of the 3.9.4 plane firmware. This is a minor update over the 3.9.3 release. Changes...
View ArticleQuadPlane and Parachute
@bovi wrote: Hi all. On my a little larger VTOL I have a parachute as an additional safety feature. My Questions, if someone, please. In QuadPlane (SERVOx_FUNCTION, 27), when the chute is deployed,...
View ArticleFull auto flights end to end
@hybrid-guy wrote: Hey everyone! I have a question about this: The landing detection logic in QLOITER mode is not as sophisticated as the landing detection logic in Copter, so if you get GPS movement...
View ArticleMatek STD external Current Sensor setup
@Devin_Tegen wrote: I want to run 8-12s Li-ion on wing I am building. That way I could let the volts do the work and keep the amps down on liion’s Is it possible to use the matek std with an external...
View ArticleClik here to view.
Quadplane with 2 Front Tiltrotors - Servo Power Issues
@jacques_eloff wrote: Hi fellow VTOL fliers, hoping for some guidance here: I am currently doing some testing on a Quadplane which has front tilting motors and have run into an issue with servo power....
View ArticleUnable to download hex files from ardupilot firmware site
@wcfung1 wrote: I am flashing an OpenPilot Revolution board with arduplane firmware. Have already soldered the SBL pads, installed Zadig driver and STM 32 bootloader. Can see the board in the COM port...
View ArticlePoll anyone using ubuntu 18.1 and arduplane? just curious I am trying to
@josheeg wrote: poll anyone using ubuntu 18.1 and arduplane? just curious I am trying to. Posts: 1 Participants: 1 Read full topic
View ArticleExtremely large Aircraft Compass Calibration
@MerkaTony wrote: Hello Mindhive, I am asked to “calibrate” a ProfiCNC 2.1 with dual Can GPS on an extremely large plane. As you probably understand by now, this is not possible to be flipped around...
View ArticleClik here to view.
I have make install to jsbsim the main page and ardupilot one I get a error...
@josheeg wrote: Screenshot from 2018-12-16 10-39-55.png1920x1080 164 KB I have make install to jsbsim the main page and ardupilot one I get a error on the black screen when I try to run a mission with...
View ArticleHelp for logging flight log
@Bruno_Barros wrote: There was a fickleness in the imu on a flight I would like help from some of you Pix cube Arduplane 3.9.4 Rvjet wing 1,95m Posts: 2 Participants: 2 Read full topic
View ArticleArdupilot support for HolyBro Pixhawk 4 Mini?
@Ed_209 wrote: Does anyone know if there will be support soon for the Pixhawk 4 Mini from Holybro? Posts: 1 Participants: 1 Read full topic
View Article