FlySky iBus RCin
@ag-sys wrote: Is it possible to use FlySky iBus? I have a 10 channel receiver but only get 8 channels via PPM. Posts: 1 Participants: 1 Read full topic
View ArticleServo gimbal travel
@ag-sys wrote: Hello,I'm using a servo gimbal which has a pan angle of 180 degrees. Currently, I send the pan output on RC7 to an Arduino Nano which scales the PWM to 700 - 2300 us, giving a little...
View ArticleFailed to send new fence points in Geofence
@Ronald_Pandolfi wrote: It seems that "failed to send new fence points" has reappeared in Plane 3.8 beta causing loading of Geo-Fence points to fail. The problem may be related to what occurred...
View ArticleHere + GPS Vertical positioning issues
@Leon_Dwyer wrote: I have been using the Here + RTK system for large area survey for around 6 moths now. And I have accumulated a good sample size of how well it is working. Currently, on ArduPlane...
View ArticleTelemetry connection get bad while calibrating compass
@FireFly wrote: Iam calibrating compass using a telemetry, and RSSI got lower and lower until disconnected. Iam using a 2.4G telemetry. I think its because the data stream is too big, anyway to set...
View ArticlePixhawk compass rotation
@zwheat wrote: Hi there, I was just wondering, does anyone know if you can setup the pixhawk in mission planner to know if it is installed in a plane off angle? Like if i installed it 90 degrees to...
View ArticleClik here to view.
QuadPlane Conversion of Volantex Ranger EX (Part 2)
@GregCovey wrote: This is the continuation of our Ranger EX QuadPlane conversion thread using APM v3.8.0 firmware. The original thread, Part 1, is in the v3.6.0 forum here. Part 1 left off where my...
View ArticleTRIM_AUTO: Automatic trim adjustment
@g00bd0g wrote: I am having difficulty trimming my plane so it is the same in manual and FBWA and FBWB modes. What I do is set TRIM_AUTO to 1. Takeoff and fly in manual, trim plane in manual, then...
View ArticleOctaPlane PWM and Motor mapping issues
@ULC_Robotics wrote: I have been working on a quadplane project for the past few months with mixed results. This airframe is a 3 meter wing span custom design flying wing weighing between 12-15kg. I...
View Article3.8.0beta6 whats new?
@MRC87 wrote: What was added with this beta 6 release? Any word on when 3.8.0 will be released? Posts: 1 Participants: 1 Read full topic
View ArticleWhat replaces RCx_FUNCTION?
@475241512 wrote: hello all, I got a question in ArduPlane 3.8.0beta5. I connect my parachute with RC7,Generally,with arduplane 3.7.1 stable,I set RC7_FUNCTION to 27 for parachute,but now,I cant find...
View ArticleFailed to create an attribute for my ADC report
@Bossipo wrote: Good afternoon, I am trying to connect an Analog to Digital Converter (this one), so I'm using the driver of the libraries/AP_ADC folder. To log the data, I created a function in the...
View ArticleOctaPlane Motor Mapping Issues
@ULC_Robotics wrote: I have been working on a quadplane project for the past few months with mixed results. This airframe is a 3 meter wing span custom design flying wing weighing between 12-15kg. I...
View ArticleReverse thrust on manual landing
@bendead wrote: Hey guys, I just learn about the reverse thrust auto landing a couple of month ago and it's pretty cool, I think the only liner using that in flight was the Concorde. BTW I am a...
View ArticleBeginner to Autopilot
@Alyaa_Ashraf wrote: Hello, I am a beginner to the autopilot drone. May I seek some help how can I setup a drone using the arduino and APM 2.6? Thank you. Posts: 1 Participants: 1 Read full topic
View ArticleIn Arduplane parameters, what is the difference between “trim_arspd_cm” and ”...
@innovation wrote: In Arduplane, "trim_arspd_cm" represents the level_flight cruise speed ，but " scaling_speed" which used to calculate the performance of PID controller also means the aim airspeed I...
View ArticleCompass Confusion Again!
@jwcalvert wrote: Questions:1) Does the HUD in Mission Planner indicate True or Magnetic North, given that it knows the declination?? 2) I have two vehicles running latest APM software; a ROVER and a...
View ArticleTransmitter Based Tuning
@iskess wrote: Has anyone tried Transmitter Based Tuning?http://ardupilot.org/plane/docs/common-transmitter-tuning.html I'm having a hard time getting a good tune on my Quadplane, especially for...
View ArticleWhat is the ADSB?
@semo wrote: hi all, I want to know what is the meaning of the ADSB and it's parameters ?? regards . Posts: 2 Participants: 1 Read full topic
View ArticlePlane 3.8beta6 motor troubles
@weliwarmer wrote: Hi, Running OK on plane 3.8beta5 and I thought I'd update to beta6 but the motor will not start after the upgrade. All looks happy but there's no output to the motor. Tested with...
View Article