Decision Tree of Arduplane Flight Stage
@kocakgillac wrote: Hello Everyone, I am new at Ardupilot Dev. I have tried to figure out how flight stage set automatically but i havent understood yet. Because there are a lot of things about stage...
View ArticleStall prevention
@pauljatherton wrote: I have only been introduced to stall prevention and the STAB_PITCH_DOWN parameter since building a new plane, so a brand new install of AP on a new Matek FC resulted in this...
View ArticleClik here to view.
Xplane SITL 4.2.0dev - GPS disable not effective
@Moha wrote: Hi Everyone, I have been using the SITL firmware for xplane (4.2.0dev) by downloading it from MP with no issues. I have disabled the gps using SIM_GPS_DISABLE = 1 and I could see the...
View ArticleQuestion about Android SDK to communicate with Ardupilot Quadplane
@nghiajenius wrote: Hi everyone, I’m working on custom Android software to communicate and control a Quadplane running Ardupilot. Could you kindly recommend me any Java SDK or example code that can...
View ArticleClik here to view.
SOLVED-wires swapped: Matek h743 compasses not showing up in mission planner
@Jacob_Pagett wrote: Hi, I have connected my matek h743 wing and matek m9n-5983 GPS together and connected to arduplane through mission planner. Under the compass priority page, no compasses show up....
View ArticleMultiple pole count for VTOL aircraft
@Lorenzo_Pessah wrote: Currently is possible to select only one pole count parameter in order to covert ESC telemetry data to actual rpm. It is quite common on some VTOL configurations to have a...
View ArticleClik here to view.
Function programed motor control
@Peter_Stone wrote: Does anyone know how Ardupilot+Pixhawk can automatically adjust the motor RPM according to the function? 1764×1247 Thanks for helping! Posts: 1 Participants: 1 Read full topic
View ArticleSerial Port 4 on Cube Orange ProfiCNC board inop for Benewake TF03 Lidar
@Tomcat-Tech wrote: PLEASE HELP WITH SERIAL PORT 4 Cube Orange. I’m trying to set up a Benewake TF03 lidar on serial port 4 on a ProfiCNC /Px4 Carrier board with Cube Orange in Mission Planner and...
View ArticleBug report arduplane 4.1.0beta5 and or mission planner
@Benc wrote: MATEKH743 wing running arduplane 4.1.0beta5 , connecting with 1.3.75 build of MP . I did a clean firmware install including full chip erase . I m getting a missing parameter error upon...
View ArticleAdjusting cruise speed
@xixijoe wrote: https://ardupilot.org/plane/docs/tuning-cruise.html#tuning-cruise I have change ARSPD_FBW_MAX from 22 to 19 and ARSPD_FBW_MIN from 9 to 6(during flight). the plane did not slow down....
View ArticleClik here to view.
Motor Setup Issue
@Silavite wrote: Howdy all, I seem to be having an issue getting my motors started up. Attempting to arm the craft results in this error. The craft is a copter type tailsitter without vectored thrust....
View ArticleGPS failure -> plane nose dive
@tkoivuro wrote: Hi all! Few days ago we experienced anomaly and loss of aircraft during low altitude mapping mission. Setup and params (might be inaccurate): Fixed wing plane Cube orange running...
View ArticleRC Fail on the latest betas
@AndreyI wrote: Hi! My configuration: Matek F765 Wing FrSky R9MM On early versions of firmware 4.1, No RC Receiver messages often appeared, this did not affect the management in any way. With a...
View ArticleTAKEOFF mode instantly ramping motors
@Ed_209 wrote: This is something that has been bugging me for a while: I have never been able to get the motors to ramp up gradually using TAKEOFF mode. When I use TAKEOFF mode, the motors instantly...
View ArticleTake off Hand launch does not flying straight
@xixijoe wrote: @allister Hello, everyone. Can I have some help here? I arm the plane heading to the direction where the plane does auto takeoff. I gently lift the plane without changing its heading....
View ArticleLack of information with NMEA frame read by ardupilot
@Nadia wrote: Hi, I’m new to this, and I’m a bit lost. Could someone tell me what are the specific NMEA GPS frames ardupilot uses to establish position? Thank you very much. Best regards. Posts: 1...
View ArticleClik here to view.
Tcal_Enable parameter request
@RizHass wrote: @tridge2, May I request that 4.1 build should include parapeter just like copter. Reason: I am working with Civil Aviation, and one of their requirement for Altimeter is “Programmable...
View ArticleRequest of Flight Logs with TECS tuned correctly
@GianLod wrote: Hello everyone, this is my first topic and I’m writing here because I’m a bit in trouble. Let me explain: Last July I did an internship in this little company that makes drones...
View ArticleStatic port for RC aircraft
@Roger_McClurg wrote: The altimeter on a FC measures the pressure within the cockpit not true static pressure. If the air pressure in the cockpit increases or decreases with throttle or airspeed the...
View ArticleModify ardupilot GPS reading
@Nadia wrote: Hi all, Does anyone know if it is possible to modify the file containing ardupilot that is responsible for reading the GPS string? I am new and I am quite lost. Thank you very much. Best...
View Article