Autonomous GEV/WIG
@svede wrote: Using the Matek H743 with barometer altitude control, ground effect pressure keeps it from accidentally landing as long as the airspeed is set correctly. Handed this project off to...
View ArticleSetting up elevon plane in Arduplane 3.2.2
@wcfung1 wrote: The latest version of Arduplane supporting APM V2.5 is v3.2.2. However, there is no SERVOn_function param in this version of Arduplane as in V3.8 and later. In Arduplane v3.8 and...
View ArticleHorizontal Bicopter with Plane (XAG Polar V40)
@prodha wrote: hi, is a system like this possible? yes it’a bicopter but i want to mix it with plane. The front servos do balance and orientation, but when switched to airplane mode, is it possible...
View Article4.1.0 dev DJI FPV OSD BUG？
@cqmiao wrote: matek-f405-WING + 4.1.0 dev，VTX is DJI FPV，The osd is ok when disarm,but osd refresh rate is slow or frozen when Arm. Posts: 1 Participants: 1 Read full topic
View ArticlePlane 4.1 Geofencing
@Giaco wrote: The Current Plane Wiki talks about the new method of entering Geofences in Plane 4.1 and after. I’m currently running Arduplane 4.0.9, (which appears to be the latest i can find) on my...
View ArticleOSD Low Airspeed Stall Warning
@Marc_Dornan wrote: One of the nice things about the old Night Ghost MinimOSD fork was that you could set stall warning based on a min airspeed to flash in the center of your OSD - these were done by...
View ArticleHere3 with can bus GPS_TYPE set makes gps2 on uart disappear
@pragma wrote: If autopilot is booted when GPS_TYPE and GPS_TYPE2 = 1, autopilot does not find Here3 in CAN, but GPS2 with uart works ok. If now GPS_TYPE is set to 9, both GPS’s start to work ok. This...
View ArticleLarge/heavy plane accelerometer calibration
@gartfeo wrote: Hi, Anyone had experience calibrating large/heavy plane accelerometer? Is there an automotive way of doing that? Posts: 5 Participants: 2 Read full topic
View ArticleArduplane SITL with X-Plane 11 - Aircraft doesn't move when takeoff
@nghiajenius wrote: Hi everyone, I tried to setup Arduplane SITL with X-Plane 11 as in this tutorial: https://ardupilot.org/dev/docs/sitl-with-xplane.html Now I have a connection between SITL and...
View ArticleWhen the accelerometer calibration is required?
@depeurvince wrote: Hi, I’m wondering when the accelerometer calibration is required after the initial setup? It is required to redo it again after firmware upgrade? How to know if it’s necessary?...
View ArticleAilerons initial position to be climbing when plane is on catapult
@gartfeo wrote: I’m trying to set the initial position of the ailerons to match the set climbing pitch angle of the plane when it is on the catapult with (18 degrees of angle). But when I switch to...
View ArticlePetition for us to choose SITL firmware version
@Shef wrote: Hello all, Too long, don’t want to read this post? : Comment “want own SITL firmware version” to sign the petition. The petition is to get the devs to implement a tool in mission planner...
View ArticleWhere is the state of the vehicle being logged in the data flash logs with...
@j0hn wrote: Hello everyone, i’m doing SITL-simulation of a quadplane with a physics backend in matlab. For the communication i use the json format just like it is done in the example for SITL with...
View ArticleUsing DSHOT telemetry in takeoff mode
@maciek252 wrote: Hello, I’ve built a VTOL plane but it’s a lot of hassle and I fly “classical” planes. I do hand launches, usually using the takeoff mode, and it’s tricky. It works… almost always....
View ArticleClik here to view.
Waypoints in google earth kmz file wrong height
@Fugazi wrote: Seems the kmz file the waypoints arent the correct height, the white line with grey shaded section, any ideas? Thanks Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Striver mini VTOL 4+1 QuadPlane
@makeflyeasy wrote: Striver mini VTOL is a 7kg vertical take-off and landing fixed wing,which inherits the safety and practical characteristics of the Fighter. 14096×3072 352 KB Material:...
View ArticleCopter Tailsitter
@pfaudette wrote: I finally got it off the ground under control. It’s a modified Stryker, with DJI phantom motors running on a 4in1 ESC. I have the hover_learn mode off at this stage. Bench testing...
View ArticleMatek H743 missing params error and no current display
@darrell wrote: I just loaded 4.09 on to a new Matek H743 Wing board. When I connect to it with Mission Planner at the end of the params loading I get an error ‘Missing Params 1195 vs 1194’. I don’t...
View ArticleSetting up Quadplane, problem with swapping parameters from an earlier...
@Virtakuono wrote: Hi. i have a problem with uploading parameters into my quadplane from earlier autopilot. My drone is a foxtech LOONG vtol, and i put in a new autopilot and uploaded plane firmware...
View ArticleProblem with TX calibration for plane
@Cattlebaron wrote: I can’t get QGC(4.1.2) to calibrate my radio (Frsky X9D+ 2019). The plane is a flying wing so I have set the SERVOx_FUNCTION to elevons i.e. Left elevon to SERVO1_FUNCTION, right...
View Article