QuadPlane flips during transition
@Robel_Efrem wrote: I’ve been working on getting a quad plane to perform an auto mission correctly for about 8 months now and crashed 3 birds so far. It’s the same problem for all the aircrafts, when...
View ArticlePixhawk angle to arduin update rate?
@Shef wrote: Hello everyone, I was wanting to feed the euler angle output (which would be supported by the airspeed sensor) from a pixhawk to an arduino? I was then going to use these angles in a...
View ArticleClik here to view.
Problem with mauch pm and boardvoltage with cube orange
@supercurare02 wrote: Hi everybody, best wiches for 2021! i have a pb with my nex orange cube pixhawk. i normally flah it with thye 4.07 arduplane firmware. install f9p gps, xlrs telemetry and power...
View ArticleElevon position in auto flight mode
@dronar wrote: Can someone tell me why in automatic flight mode (after takeoff), the elevons take that position? Shouldn’t they be up? (video) https://youtu.be/i1tCw8NSRx8 Posts: 1 Participants: 1...
View ArticleAverage cell voltage on the OSD
@stavros wrote: Hi everyone, I have an Omnibus F4 and would like to see the average cell voltage (rather than the sum) on the OSD. Is there some way to do this? OSD1_CELLVOLT_EN doesn’t show anything...
View ArticleAuto VTOL mission without heading to WP when doing transition to fixed wing mode
@mirkix wrote: Hello, is it possible to create an Auto VTOL Mission that takeoff vertical and then when doing the transition to fixed wing mode will not try to change the yaw angle to the next...
View ArticleClik here to view.
Searching for Plane/Multicopter Log files
@ManInNight wrote: i am searching for flight logs from a fixed wing and multicopter (position, speed and acceleration are the most interesting). They should flight in a straight line on windy...
View ArticleIssue with Servo Movement using X8R and Pixhawk for VTOL
@saintofinternet wrote: embarked on the VTOL journey with Y3 setup. using a Frsky X8R with SBUS connected to the Pixhawk RC IN the Ardupilot Radio Calibration screen in Mission Planner does show the...
View ArticlePreflight sensor calibration
@NorbertK wrote: Could be implemented a preflight sensor (e.g. analog airspeed sensor) calibration, triggered through an RC switch ? This way we could eliminate the need to connect the FC to MP or QGC...
View ArticleBad compass health plane 4.0.7
@oguzhan wrote: Hello, I installed the latest arduplane version(4.0.7) on my matekf405-wing card. I’m getting an “bad compass health” error even though I use a compass. I marked all compasses as...
View ArticleFirst time ardupilot user needs some help
@AeRiAL_PeRpLeXiOn wrote: hello there, this is the first time using Mission planner and arduplane but i do have experience with betaflight so im not a complete rookie I have a matek f756 wing that i...
View ArticleClik here to view.
Velocity Problem in Gazebo
@huseyinkpilot wrote: Hi everyone, In gazebo for plane, when I send command to increase velocity, the plane doesn’t handle it. The velocity is still constant. The other things is ok for me. Just...
View ArticleBenewake TF-Luna 8m LiDAR for plane
@AJack wrote: I would like to equip a plane with this lidar for landing assistance and testing, anyone has experience with this lidar ? will 8m stated measuring distance be useful ? Thanks! Posts: 2...
View ArticleClik here to view.
WLTOYS HK450 as ARDUPLANE VTOL
@Satsepp wrote: Hi, sorry about my english. I build with lot of Help from Rolph my HK450 as Arduplane for FPV usage. So i simply removed the original board, and replacet it with Matek F405 Board, CRSF...
View ArticleClik here to view.
Servo7_function=39 not working in VTOL
@saintofinternet wrote: so as per the document at https://ardupilot.org/plane/docs/guide-tilt-rotor.html i have setup a non vectored yaw VTOL using Arduplane in the Y3 config. as per the setup i have...
View ArticleWonderful Input on VTOL Emergency Fallback by Greg!
@saintofinternet wrote: Continuing the discussion from Setting up a new Vectoring Quadplane: Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
QLOITER Take-off problem on QuadPlane
@mr.bigby wrote: Hello there, We have attempted take-off with QLOITER but we had some problem and moved on with QHOVER mode. As you can see from the pictures below at takeoff it attempts to change to...
View ArticleClik here to view.
Q_WP_SPEED_DN -- does not work on QuadPlane Land first stage
@OrionCarlos wrote: Hello friends I am trying to configure the speed of descent of the quadplane in the first stage, but it seems that there is no such function (LAND_SPEED_HIGH) for quadplanes … I’m...
View ArticlePlease help with USB game controller issue for payload control
@Trev1 wrote: Hi all this will be my first post here but lots of years of reading and this is the first time I cannot find an answer. Below is our problem I have integrated a payload into our fixed...
View ArticleCrsf protocol with ardupilot
@Kristiqn_Ushatov wrote: How to connect the Rx with the FC. The receiver Rx to TX of the FC , and the receiver TX to RX of the FC. The rx and tx ports of the FC to be of 1 uart. And to set 23 (RCIN)...
View Article