ArduPlane Gazebo-Zephyr SITL launches with propeller spinning
@Barbara_Flindt wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Unable to find crash cause!
@Sunny52266 wrote: Hello all. I have searched the forum to find a similar issue but can not find one. I had a strange crash during takeoff today and I have tried my very best to find the cause...
View ArticleClik here to view.
Problem servovoltage Pixhawk v2
@Paola_Casabona wrote: I I have two servos in a plane(VTOL X8) with firmware 3.10.0. Sometimes, the value of the servovoltage is 2, 12, 9 V . Do you know if this is a problem in the configuration? I...
View ArticleMatek F405 Wing
@Hally wrote: Hi guys can anyone please tell me what settings to use for SERIAL 2 on my Matek F405 Wing board to get SBUS to work? Arduplane version 3.9.11 and the receiver is an Openlrsng unit. TIA...
View ArticleMatek405 wing GPS/Telemetry problem
@Jregholdsworth wrote: When I try to connect to the matek 405 wing using either Bluetooth or 433mhz radios I have the same problem. If GPS is connected Mission Planner fails to connect and times out....
View ArticleClik here to view.
Stability Issues Delta Wing in FBWA
@Engnr_Mirza_Khurram wrote: I am using Cube on a custom made delta wing platform. In FBWA mode bird stability is very abnormal and in both takeoffs that I have tested, bird has flipped resulting in...
View ArticleHow far from cg can I mount the flight controller in a delta wing
@Rusty_Jones wrote: I am looking to install Ardupilot in a flying wing and space might be tight. Most of the center of the wing will be battery or ESC / Motor. There is some space about 3-4 inches...
View ArticleAre there any actual devs in this forum?
@jumpwing wrote: Are there any actual I am writing this out of extreme frustration… I am trying to build a tiltrotor tricopter where all 3 motors tilt -the design is 2 meter, efficient, and built of...
View ArticleTailsitter VTOL
@Salex wrote: Hi, I’m building the tailsitter. 2 servos for ailerons and 2 motors. I activated the qplane mode. Motors configured to 33 and 34 function. How should i configure the function for...
View ArticleHow to collect the alpha ,beta data from pixhawk cube
@Sampath_kumar_Chirut wrote: am using pixhawk cube black. right now am connected to potentiometer to ADC port . then after after calibrated accel , compass,…,. then after armed and downloaded the DF...
View ArticlePX4 RC Ch8 no PWM servo output
@Nola66 wrote: My setup Taranis X9D+ and crossfire on a pixhawk PX4 using mavlink for control. All IN/OUT correct on Taranis. I can see the channel(RC CH 8 RC PASS THROUGH) in the radio calibration...
View ArticleReading CAN BUS data from can port on pixhawk to RPI
@Brian_Duvall wrote: Hello all, I am trying to read Raw IMU data from a pixhawk one to a RPI 3 useing UAVCAN. UAVCAN has this standard definition: uavcan.equipment.ahrs.RawIMU Is this possible to do...
View ArticleDynamic home position for plane out at sea
@explorer_mel wrote: Hello everyone, I’m trying to figure out how I can have a dynamic home position for my fixed-wing drone. I fly out in the ocean and BVLOS and the arming/home point is on a vessel....
View ArticleMatek F765 Smart Port Telemetry with ARDUPILOT
@Min_12 wrote: (topic withdrawn by author, will be automatically deleted in 24 hours unless flagged) Posts: 1 Participants: 1 Read full topic
View ArticleMatek F405-Wing Autonomous Mission using Mission Planner
@RizHass wrote: I am interested in F405 FC (fixed wing) but before I spend any time on this, has anyone tested successfully auto missions? Any issues? Thanks Posts: 1 Participants: 1 Read full topic
View ArticleArduPlane Firmware 3.2.1
@benm wrote: Hello, I recently got an Ardupilot 2.8 controller board, which will not work with the latest firmware. I want to download the firmware from version 3.2.1, but the only ones that are...
View ArticleClik here to view.
Hardware mounting in small plane
@yak-54 wrote: Hi all thanks for great work you all have done anyway i was going to testing of 4.0 betea on BF3.2 Omnibus F4 V2.1Flight Controller in a mini skywalker this is the onlyway i can mount...
View ArticleDate and time display on OSD using integrated OSD chip on F4 boards?
@ninja_zx11 wrote: Hi all, Is there any way to display date and time on OSD if running arduplane on omnibusF4Pro board with GPS? I tried to search and found that its possible on minim OSD.I even tried...
View ArticleFailsafe not working Matek F765
@Min_12 wrote: Hi guys, using a matek F765 with the only available firmware which is: 4.1.0-FIRMWARE_VERSION_TYPE_DEV With an RX6R using ACCESS protocol. When setting failsafes on the Taranis, i...
View ArticleVTOL simulation in gazebo
@Barbara_Flindt wrote: Hi, I’m trying to setup a simulation of a quadplane in Gazebo. I’ve added an entry in vehicleInfo.py, I’ve created a .parm file with INS calibration and I have a quadplane model...
View Article