Rx rssi no longer working?
@jace26 wrote: I just made the jump from plane 3.8.5 to 3.9.9 and noticed that my rxrssi user-item on the MP HUD no longer works, its just zero’d. No change to my hardware setup or parameters. Using...
View ArticleAdding custom flight mode Qgroundcontrol
@AWE_student wrote: Hello everyone, i got a custom flight mode, which runs fine in in SITL using jsbsim. Now i would like to make it seen in QGroundcontrol to use it in a real flight. However i am not...
View ArticleOmnibus F4 Pro V2 build by using Zohd Nano Talon
@Nelson_Lee wrote: Hi all master, I am new for plane and just bought this ZOHD Nano Talon and Omnibus F4 Pro V2 try to build Arduplane, after flashed the Arduplane v3.9.9 and connect all the wiring...
View ArticleProper ESC Wiring
@kerrycorcoran wrote: I have the Signal and GND wires plugged into S1 and GND on my Flight Controller. I don’t recall where I saw this, but I made sure I did NOT connect the red wire to the Flight...
View ArticleSpektrum satellite receiver not working with omnibus F4 pro
@Niels_Daemen wrote: I want to use this spektrum satellite reciever with this Omnibus F4 pro v3 (Both flight controllers have the latest arduplane 3.9.9 OFFICIAL firmware installed) When I first...
View ArticleClik here to view.
Use Arduplane as EFIS in experimental or UL manned aviation
@flightzoomer wrote: There was a thread some years ago, asking whether a Pixhawk could be used in a real airplane. I can perfectly understand, why the feedback from the Ardupilot community was...
View ArticleClik here to view.
Two silly unexplained crashes
@armadillo wrote: Hello, I just had two fairly odd crashes in one day (no damage) but am completely baffled about why they happened. The .bin can be found at this link. The log contains three (very)...
View ArticleTips/tricks for high aspect ratio single motor tail sitter?
@linuxguy123 wrote: I need to build a high aspect ratio single motor tail sitter plane. Kinda like a motor glider tail sitter, but with a lower aspect ratio. It only needs to prop hang to take off and...
View ArticleClik here to view.
Need Help, cant reflash firmware for 2.4.8 to Plane Mode
@PcoleZoey wrote: Background: I have my quad and tricopter firmware working but now I want to rollover to fixed wing. Ive always had connect issues, it seems all versions and many people have all...
View ArticleClik here to view.
Plane 3.9.10 release
@tridge wrote: ArduPilotPlane.jpg750×291 33.1 KB I’ve just released 3.9.10beta1. This has one important change in the IOMCU UART handling. The change stems from a flight log showing a short (under...
View ArticleTilt Rotor, Quadplane with two front tilting and sudden pitch in forward...
@Prem_Sai wrote: Hi community, I am building a quad plane with front two motors tilting and rear two motors fixed. while I am doing the transition from Qstablise to FBWA, the plane pitches so hard and...
View ArticleMatek Wing F405 Bad logging error 3.9.9
@Solhead wrote: Hello, I have updated the Matek Wing F405 from version 3.9.6 to 3.9.9 and without touching anything at all, I get a Logging error and it doesn’t let me arm. I have changed and...
View ArticlePower surge from the battery connector wiped out accelerometer calibration...
@ninja_zx11 wrote: Hi all, Today i learnt a new lesson about the severity of a power surge!! I was testing my camera on my plane equipped with OmnibusF4ProV3 running Arduplane.I have a huge low esr...
View ArticleMatek f405 CTR wiring issues
@woogie_man wrote: Hey guys… .I am sorry to be “that guy” starting a thread and asking for help. I was using another system and had a few crashes that were due to software issues, and I was wanting to...
View ArticleClik here to view.
VTOL exceeding groundspeed limit
@jace26 wrote: The other day I was bringing a VTOL plane ( with 3.9.9 stable) back to its take-off location from some distance away in QLoiter, when I noticed visually that it seemed to be traveling...
View ArticleSplit one input into two servo's (functions)
@ON7AMI wrote: Hello, New to the whole project I’m very exited of it. Before I read all the documentation I had a question: is it possible (without intervention in the software) to split the input of...
View ArticleHow accurate and precise are Arduplane's groundspeed and heading?
@linuxguy123 wrote: Hi people. Assume a plane is flying in a straight line, level flight at a constant power setting. Assume that the GPS unit has a good fix on as many satellites as it needs. How...
View ArticleHardware, software or some kind of runtime calibration error?
@Redshifft wrote: Nasty crash on launch, log and video (sorry for quality) Ideas? https://mega.nz/#!ydI03CBA!i7MedVsCcxgRzpweAj_SxFoCXs3ejCMhht1ZJEB_ykw Posts: 1 Participants: 1 Read full topic
View ArticlePixhawk temperature sensor for engine
@Engg_Ya_r wrote: hello if any one cant help me iwant to know my engine Temperature i used type k sensor temp but how ican connect the sensor with pixhawk or any temp sensor i used mission planner...
View ArticleClik here to view.
TBS Crossfire (868Mhz) and 900Mhz SIK radio
@omnidirectional wrote: Hi guys, I’m currently using the TBS crossfire system for long range automated flying with the Pixhawk Cube. I have the TBS receiver (on the aircraft) wired to the Pixhawk via...
View Article
