What parameters are needed to make 3 motors tilt on a tricopter
@jumpwing wrote: Trying to develop what Kris made here… he has published his parameters but I cant get them to work… Im using a pixhawk4. any ideas would be appreciated. Thanks Posts: 1 Participants:...
View ArticlePlan de vuelo para aerofotogratria
@Maxi_Kromm wrote: Buenas tardes, tengo el problema de que en los planes de vuelo generados para un vuelo fotogramétrico con un dron de ala fija, las lineas de vuelo no se generan a una equidistancia...
View ArticleWhere do I position the throttle for auto takeoff?
@wsalopek wrote: I have looked and looked (and looked and looked) for this answer…but can’t find it… Where do I place the throttle for auto takeoff? Indeed, what is the procedure? The docs don’t...
View ArticleClik here to view.
RC_CHANNEL_OVERRIDE command doubts
@Airman01 wrote: Goodmorning community, i’m trying to fully understand mavlink and i’m facing a problem. I have a plane that i want to control using arduino by sending command to my PX2 (cube). The...
View ArticlePixhawk reboot after fast rising from min throttle to nearly max throttle
@mauris wrote: I rebuild my flying wing due to summer update… During motor test (on ground, manual flight mode), the board has restarted after fast rising from min throttle to nearly max throttle (not...
View ArticleClik here to view.
NO RC Receiver (lockup between flight controller and receiver?)
@reluctantgithubuser wrote: NO RC Receiver (lockup between flight controller and receiver???) Airframe: Nano Goblin 600 mm flying wing System: Omnibus F4 Pro V3 Arduplane v 3.9.4 (Chibios) Companion...
View ArticleSITL with jsbsim and custom aircraft model
@smathisen wrote: I have been using ardupilot with SITL simulation for some time, using my own custom aircraft model and the JSBSim simulator. However, now I can’t get the simulation up and running. I...
View ArticleGuided_enable command
@Stephane_B wrote: Hello, I’m flying arduplane 3.9.8 I would like to use the GUIDED_ENABLE command in flight plan GUIDED_ENABLE is available in arducopter flight plan but not in arduplane I’m trying...
View ArticleClik here to view.
5 Motor VTOL controlled via PixHawk
@iSkyMaster wrote: Hi, I have seen documentation on PixHawk Supporting VTOL config. How would Pixhawk handles the 5 motor config? I am familiar with the H frame 4 motor config. Channel 5: Front right...
View ArticleLoiter too large
@Greg_Wood wrote: I’m attempting to setup a small plane using a matek 405-wing running ardupilot 3.9.7. I am seeing some strange behaviour in loiter mode. It seems like the WP_LOITER_RAD is not always...
View ArticleVTOL for mapping with Sony A6000?
@MickeM wrote: What VTOL-plane do you recommend for mapping with a Sony A6000-camera? I am used to MFE Believer which there is a VTOL-kit for, but that is a plane that have been converted. Maybe it is...
View ArticleBig Vtol Need Advice on Propeller and Power System
@ton999 wrote: Hello guys, I plan to build a big Vtol quadplane with MTOW about 60 kg. I have built several small Vtol without any problem before. I use eCalc for power system calculation which I...
View ArticleAirspeed auto tune problem
@Sampath_kumar_Chirut wrote: hi am using pixhawk cube (black). aircraft model is flyingwing . am given cruise speed 20 at the same time i change the parameter arspd_autocal =1 for auto tuning purpose....
View ArticleWhen am gave the full throttle it is not given full thrust
@Sampath_kumar_Chirut wrote: am using pixhawk cube black . frame is flyingwing . am initially change the parameters is L1 period is give 19 and airspeed cruise is 20 then after arspd _autocal gave 1,...
View ArticleArdupilot and digital terrain models from Kartverket (Norwegian Mapping...
@supermag wrote: Hi, I am curious if it’s possible to implement the free and open DTM10 data from Kartverket. It’s in 10x10 meter grid measurements, with a accuracy of ± 4 to 6 meters,as it’s superior...
View ArticleFolding Propeller Stuck During Flying (quad motor) , need advice
@ton999 wrote: Hello guys, I plan to build big Vtol Quad plane by using big Folding propellers for the quad motors (36 inch propeller). However I am worried that the folding props may stuck in the air...
View ArticleWhy is the Q_TILT_TYPE=3(Bi-Copter)75 76 servo not working?
@sheyao wrote: Why is the Q_TILT_TYPE=3(Bi-Copter)75 76 servo not working? Is it set up like Y3 X4? I applied the Y3 settings directly. The left and right tilting servos did not work. Posts: 1...
View ArticleRTL mode the plane speed is gradually decreasing
@Sampath_kumar_Chirut wrote: hi am using pixhawk cube black . am initially tuned my plane , then after i reset the all parameters and again i gave the PID tuning values , then after in FBWA mode i...
View ArticleClik here to view.
E-Flite mini-Convergence with ArduPilot
@kd0aij wrote: The E-Flite Mini Convergence is a smaller version of the original Convergence VTOL. It came out about a year ago: RCG thread Recently the PNP version has been on sale for only $80, so I...
View ArticleWhat Parameter To Set To Avoid Crash During GPS Glitch Problem or Bad GPS?...
@ton999 wrote: As we know that some times during flying it may happen GPS glitch or bad Gps. So my question is how to anticipate this GPS issue?? What parameter to set to avoid crash if this problem...
View Article