VTOL, TRI Rotor, Yaw control with rudder in hover mode
@Timmy_Lassie wrote: I have almost finished building a VTOL tri rotor vehicle based on the Finwing Transformer airframe. It differs from any other vehicle i have seen in one way. the vertical...
View ArticleScorpion esc beeps using pixhawk 4
@i1ya wrote: Hello dear arduplane users, I’m using: pixhawk 4 with arduplane V3.9.8 (latest) mission planner 1.3.66 ESC and motor are both by Scorpion. I connect “FMU PWM IN” from pdb (power...
View ArticleSkywalker x8 VTOL DIY
@panahi wrote: Hi, I want to make my X8 a VTOL plane. i have seen this post and i plan on doing the same but i would like to maximize my flight time and my effiency. i’m using Scorpion 4020 540KV as...
View ArticleAPM 2.X to Arduino Communication
@picibo12 wrote: i have a project to make a parachute control using apm 2.8. this board not support ac 3.3+, so i want to modify it using arduino. and i get confused how to send data from apm to...
View ArticleNo more update firmware for Kakute F7 DEV
@Tony2k wrote: Why there are no more updates for Kakute F7 Arduplane DEV? Latest is from 21 May. http://firmware.ardupilot.org/Plane/latest/KakuteF7 Posts: 1 Participants: 1 Read full topic
View ArticleS.BUS switch channels 17 and 18
@TunaLobster wrote: I have a T18SZ. I can use channels 1-16 just fine, but I am not seeing the ability to use the 2 switch channels. I see that the Linux HAL has the code to use them on the master...
View ArticleMatek F722 Wing
@DonaldHill wrote: Hi Is there any plans to shortly have the Matek 722 Wing available as an FC for ArduPilot Plane? Just would like to know before I go and buy a 405 Wing again. I already have a brand...
View ArticleClik here to view.
VTOL TIlt Rotor with 2 front rotors tilting
@Jim_Hunter wrote: any idea what all parameters to define while trying to fly a VTOL Tilt rotor with the front 2 motors tilting. We have given frame class as Tailsitter and h frame type. Our...
View ArticleClik here to view.
Dangerous RTL from 145 to 50
@bendead wrote: Hi guys My Nimbus VTOL did a really dangerous RTL yesterday, instead of climbing or keeping a height above arming point, it gradually made a descent until reaching 50m. A few points :...
View ArticleCrash in the exchange of flight modes
@Bruno_Barros wrote: Hello everyone, it follows description of the aircraft that I have: Pixhawk 2.1 (cube); Firmware 3.6.9 if chibios Futaba t6j sbus reciver; Rdf 900 if castle bec 2.0 Digital...
View ArticleNo dataflash logs to download
@jmatt1998 wrote: Hi, I know this is a common problem but I am unable to get the dataflash logs to record. Currently I am not flying but just testing the board trying to record data while it is...
View ArticleBarometer (press_abs) info ERROR
@BobJ wrote: Dear all My pixhawk 2.4.8 show a value of press_abs=460.50, but the correct information at my city is near 1010.00. It is a big difference, and to me it is very importante to know the...
View ArticleRTL during LANDING on Quadplane Triggered by Low Battery
@ovolkmann wrote: Hi Guys, I thought the issue with VTOL platforms going to RTL on battery failsafe was fixed in the latest firmware version but sadly, it doesn’t seem to be and almost cost me the...
View ArticleLoiter speed too fast
@Donnerbraten wrote: Hi, Im new to arduplane, but experienced with arducopter, and Im wondering why my plane loiters with about 150Km/h (100%throttle) and about 90° roll angle. I dont have an airspeed...
View ArticleError GroundSpeed in Auto mode
@Alfian_Hermawan wrote: I have a problem with groundspeed in my flying wing. I have set a flight speed of 12 m / s, but when I do a mission with auto mode, the speed increases to 22-24 m / s. the...
View ArticleADS-B altitude filtering
@Liam_Flavin wrote: Hi, I’m trying to put altitude filtering into ArduPlane 3.9.7. I’ve got 3.9.7 and the latest ardupilot on github (3.10dev, which has altitude filtering) and they both build and...
View ArticleMoving Base icon on map
@Aticof wrote: I can connect my GPS and see the lilac Rally Point icon on map. Positioning the mouse over this icon appears Alt above sea level (absoluta Alt). The drone is positioned on the Rally...
View ArticleBuilding a new tricopter flying wing tiltrotor with 3 motors tilting... need...
@jumpwing wrote: Been working on a flying wing tricopter for a while now using QGC and had no luck getting what I need. I saw a person in China make what I needed using Arduplane and I am hoping to...
View ArticleIs Zala-Lancet-like configuration supported by arduplane? How?
@Raviu8 wrote: If I would have a plane with wing/tail configuration much like Zala Lancet How can I configure control surfaces on arduplane? It has 4 airlerons and 4 elevator/rudder . Posts: 1...
View ArticleRTL Mode and Loiter Points Coding
@alinscodes wrote: Hi. I want to make some changes. When plane goes into RTL , the plane goes to nearest rally point, but I want it to stay there for 5 minutes for example or circle 5 times (currently...
View Article