IO uControler on Cube ChibiOS
@abarnas wrote: Hello I want to change GPIO pin assignment (SPECTRUM_PWR_EN) for IOMCU, and previously when i used PX4Nuttx it worked but after migration to ChibiOS it has no impact on board. Where...
View ArticleMounting the flight controller away from the centre of gravity
@disgruntled-patzer wrote: Hello, I am preparing to mount a Cube flight controller on my quadplane (which was redesigned after a previous crash in the following post). I notice from the following...
View ArticleClik here to view.
There is no change in Pitch PID after Autotune
@kdrdgn07 wrote: Hi. I have tried to make autotune in my plane and I have did almost 30 times pitch up and down and also roll right and left. I can see the change in roll after the tune in basic...
View ArticleAnalogue RSSI on ADC port on a Cube
@yak-54 wrote: hi all sorry to ask here after some days i am trying to inject analogue rssi into ADC on a Cube running ArduPlane V3.9.8 is there an issue with ArduPlane ? Posts: 1 Participants: 1 Read...
View ArticleProblem flashing to OmnibusF4pro
@seven4 wrote: I’m having trouble trying to flash firmware to my OmnibusF4pro. I downloaded the current Ardu hex, am using the current Betaflight configurator, putting the F4 in DFU, but when i select...
View ArticleClik here to view.
How to do digital airspeed sensor calibration
@Sampath_kumar_Chirut wrote: hi am using pixhawk 4 v5 when am using airspeed sensor .the dose not showing any of data and at the same time when am arming am get a airspeed error . please any body help...
View ArticleInverted elevator on flying wing tilt rotor
@socke7 wrote: Hello, this is my first post here as I’m just run into trouble while setting up my first VTOL with latest Plane 3.8. It is a flying wing, so I’ve setup the control surfaces as Left and...
View ArticleQuadplane Spektrum DX6 (not 6i)
@Tim.Talon wrote: Can I use a DX6 for a quadplane? And is the a wiring diagram for the servo setup for a Pixhawk4? Sorry for the basic questions… New to Ardupilot and Pixhawk4. Posts: 1 Participants:...
View ArticleArduPlane3.4.0 ppm frames
@onepilot wrote: Hello, installed qczek lrs ppm output system on apm ArduCopter 3.2.1 and channels has no reaction, but with ArduPlane 3.4.0 works fine. What is the difference between ArduCopter and...
View ArticleClik here to view.
VTOL Quadplane questions after first flights
@hurzburg wrote: Just flew a Convergence tilt rotor thru transition for the first time, including all airplane modes and QRTL, Qhover,etc (successfully by the way ) and now have a question: Is there a...
View ArticleAutothrottle in manual mode
@N_A1 wrote: Hello there, does anyone know if it is possible to use autothrottle function in manual mode similar to a functionality that is found in most commercial jet aircrafts (autopilot off, but...
View ArticlePixracer Arduplane 3.9.8 bad log files
@zjl715 wrote: I am running Arduplane 3.9.8 on a pixracer the plane itself seems to be working just fine I I was testing it in VTOL and it doesn’t seem to log more then a a tiny blimp. It shows a min,...
View ArticleClik here to view.
DF Log via Mavlink
@wcfung1 wrote: I maiden my Volantec Ranger EX 757-3 running Pixhack flashed with Arduplane V3.9.6. When I came home and downloaded the log, I got the error message as attached. I also attached the...
View ArticleOmnibusF4pro telemetry
@artemen wrote: Hi, is telemetry port limited to mavlink on OmnibusF4pro? It seems that I can’t get frsky (uninverted) to work on it. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Crash after "EKF2 IMU0 is using GPS" and different AHR2 and ATT Attitude...
@Rolf wrote: Unfortunately, my new Opterra 1.2 flew into the ground in FBWA-Mode - not responding to full pulled elevator stick: After the start FBWA worked fine. Then i switched to autotune. As the...
View ArticleClik here to view.
Arduplane on brain fpv radix fc?
@itsfishi wrote: Any chance we will see arduplane for the radix fc. looks like a very interesting board when coupled with their wing pdb 8s capability current sensing etc Love all the work you guys do...
View ArticleOptimal current draw on 10-15kg airplane
@hans123 wrote: Hi! I’m looking for info about how much normally typical 10-15kg airplane draws current? at 28m/s As much I found in the logs, it’s around 50A (cruise) Maybe somebody with experience...
View ArticleCustom motor mixer for VTOL
@3dcadfreak wrote: Hello, Please point me in the right direction. I have built a pretty normal VTOL from a plane with four (non-tilting) lifter motors. As I tilted the motors in certain directions (3d...
View ArticleClik here to view.
Omnibus F4 SD - Telemetry via serial modem fails to load parameters
@Daniel_Riley wrote: I have two Omnibus F4 SD boards (the AKK version) and they both are unable to send parameters to my GCS. In QGC I get a warning saying “unable to retrieve full parameter set from...
View ArticleVTOL airraft went in to spin mode after 5 seconds of transition
@Hari_prasad_jain wrote: Hello Guys, I have attached a log file for my vtol flight which took place on 4th July, 2019. Plane took off in vtol mode to a height of 15 metres and was made to follow the...
View Article