Pixhawk burn the digital servo when I added the parachute function
@111156 wrote: Hello everyone. I am using the pixhawk with a flywing for mapping. I used to use a switch to release a parachute and it worked well. Today, I am using the parachute function to release...
View ArticleDetecting a stall
@GoFast124 wrote: Does Ardupilot detect if a plane has gone into a stall? if so, what does it use to do this? Does it use airspeed, pitch of aircraft or something else? Posts: 1 Participants: 1 Read...
View ArticleSmart Audio on ChibiOS
@Alexander_Perez wrote: Hi there. I was hoping if someone can help me. I’ve been working with the latest plane release using ChibiOS on a Matek 405-Wing board. Everything thus far works flawlessly....
View Article[HELP] Fpv & Arduplane setup
@Syliaz wrote: Hello, My goal is to see a real-time image from my plane, I would like it to be able to go about 4km away, as a ground station is too expensive, is it possible to use arduplane with...
View ArticleJerking flight mode transitions
@Alexander_Perez wrote: Hello. I’m using a Matek 405-wing with ChibiOS on Arduplane (latest released). I’m noticing on the bench when I transition to different flight modes, the control surfaces...
View ArticleClik here to view.
Nimbus 1800 tri-vtol rear motor wiring
@jimid wrote: First off, I would like to thank Greg Covey for all he does on this forum. He inspired me to build a VTOL Bixler last year (second one flew great , and this winter I built a Nimbus 1800...
View ArticleV-TAIL mixing Arduplane 3.9.7
@sergio wrote: Hello guys, I am not able to configure the V_TAIL mix in ARDUPLANE 3.9.7 after several days trying. The problem is that when I roll right the roll rudder mix causes the tail surfaces to...
View ArticleNeed help on how to customize flight modes
@Ashwin wrote: Hi all! I am pretty new to drone flying and testing, but have managed to build and do flight tests on a custom-built quadcopter, using PixHawk and Ardupilot! As a part of my project, I...
View ArticleClik here to view.
Rally Point Not working
@alinscodes wrote: Hi, so I am trying to get the plane simutator to go to closest rally point when in RTL mode but it is not doing it. Here is the mission and explanation of what happens. This is what...
View ArticleClik here to view.
Does the software support BiCopter configuration
@ITZIK_RONEN wrote: Does the software support VTOL in configuration with only two motors? Like BiCopter, using two vector motors? Screenshot_20190419-000605_WhatsApp.jpg1241x731 386 KB Posts: 1...
View ArticlePixhawk2.1 the cube Max and Min operating temperature
@aissi wrote: hello everybody, i want to ask you, if someone have any manual about the working temp of pixhawk2.1 the cube. BR. Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Regarding the issue of fixed-wing patrol speed
@PIXMAV wrote: hello, I tested my linux flight control today and flew an automatic route on the fixed-wing platform, as shown in the figure: QQ截图20190420155658.jpg1928x1058 224 KB the log shows that...
View ArticleAPM 2.8 elevator in RTH mode
@letruong006 wrote: I am using APM 2.8 circuit for X-UAV minitalon. In RTH mode, my plane increased dramatically to achieve a safe height value, the height increase is probably too large, so it tends...
View Article"Bad or No Terrain Data" error message
@Taipan wrote: I have an Omnibus F4 Pro ver3 FC board running ArduPlane V3.9.7 that I am setting up on the bench. Everything is working fine so far, but I have a query. I get an error message in...
View ArticleClik here to view.
Rapidly fluctuating battery current-draw readings
@Taipan wrote: I have an Omnibus F4 Pro ver3 FC board ArduPlane V3.9.7 that I am setting up on the bench. To calibrate the current sensor, I connected a 4.2 ohm/40W resistor where the ESC will be...
View ArticleMatek F405 wing and GPS set up advice please
@MartyMcFly wrote: Hi every one,im setting a Matek F405+matek gps up for a plane what settings do I put in mission planner compass please and do I calibrate as normal,many thank’s in advance Posts: 5...
View ArticleAutoTrim Question AP 3.9. Ailerons fully deflected on landing
@Marc_Dornan wrote: I have been flying a Nano Talon with the latest version of Arduplane and I have had a few good flights. I am using the Auto Trim feature. When I landed today after a flight with no...
View ArticleClik here to view.
Plane 3.9.8 release
@tridge wrote: ArduPilotPlane.jpg750x291 33.1 KB I have done the first beta release of the 3.9.8 stable release. This is a minor release with some important safety fixes. The fixes relate to two...
View ArticleRPM in Arduplane-3.3.0
@joucknuckbr wrote: Hey guys, I have a Arduplane-3.3.0 and I want to read RPM from a external sensor(AUXPIN) but that board doesn’t have the RPM parameter by default. Does anyone knows if I can do...
View ArticleSetting up and checking the flight controller Holybro Pixhawk 4 FW V 7.9.4...
@egunak95 wrote: Setting up and checking the flight controller Holybro Pixhawk 4 FW V 7.9.4 Ardupilot https://youtu.be/7z-ZBI1EMh8 for the project self-contained flight glider in thermal flux...
View Article