What is the digital_input logic cutoff?
@007trains wrote: I'm setting up a camera with arduplane and i'm connecting the feedback from the camera to pixhawk pin55 but the signal is too small to trigger cam messages. I plan on amplifying the...
View Article3.6 Not trimming both control surfaces in separate ports
@Autonomost wrote: I have dual elevators setup and a rudder. I adjust the trim for each elevator but it only trims one elevator? I reinstalled the firmware and thought I had solved it but the issue is...
View ArticleClik here to view.
Mission Planner Geotagger will not read log. Plane 3.6
@bchristal wrote: Just upgraded to 3.6 and flew a photo mission. Mission Planner gives the following error. Log file attached. Pasted image667x572 15.7 KB Posts: 1 Participants: 1 Read full topic
View ArticleQuad Plane Function
@garlandk wrote: Guys I am pretty new to Quad Plane, but not Copter and Ardu Plane. I have my aircraft setup. I am running four quad motors and one pusher motor. The pusher motor is setup just like...
View ArticleHow to designate transmitter switches to relays in APM:Plane?
@Autonomost wrote: So I am trying to set some relay switches up to certain switches on my transmitter, but everything online links to arducopter. http://ardupilot.org/plane/docs/common-relay.html I...
View ArticleGeotagging Issues APM Plane and Zubax UAVCAN
@Jcooper21 wrote: When flying a survey mission using Zubax GNSS 2 mission planner is always complaining about compass issues. The plane will fly the mission however all the geotags have the exact same...
View ArticleRTL adjustement
@patricestrasbourg wrote: Hello everyone I am using Ardupilot for scientific plane. For my first time i have a communication failure for the telemetry. So the plane was very hight in the sky ( 500 m )...
View ArticleClik here to view.
Discrepancy between CAM and TRIG log
@Kyomo_Jung wrote: cam_trig.png974x251 15.5 KB Hi guys, Test Environment.No GPS ( Indoor ).AP3.6.0.Nex 7.Camera shooting : by MP - "trigger cam now" As you see above picture, there might be some...
View ArticleClik here to view.
Throttle stuck wide open - Plane 3.6
@bchristal wrote: There's another similar topic as well. Might be a serious bug. http://discuss.ardupilot.org/t/lost-throttle-control-in-manual-mode-full-throttle/9641 SetupPlane 3.6Zubax...
View ArticleI need to map a Kill switch for an IC plane to AUX 3
@Autonomost wrote: I have a plane that is using all 8 main servo outputs. One of the AUX channels, not 5 as I am using that for RPM, needs to control an optical ignition kill switch for my motor. I...
View ArticleAltitude issues in Loiter, high Nav pitch demand, abrupt crash in Fly by wire
@Nihal wrote: Hi, I had a routine flight for an hour or so with my pixhawk in arduplane 3.5.2. The plane flew well for about fifty minutes or so in auto. After that, I switched to loiter a couple of...
View ArticleFormation flying with arduplane
@yuval wrote: Hello,Recently me and my friends started flying a formation of FPV planes.I have noticed that finding my friend plane while flying is really hard and takes some time. I was wondering if...
View ArticleCant DisArm Board
@Buzzliteyear wrote: Hi All, I decided to have a go at Ardupilot again after few years and got the ebay special 2.8 board install ArduPlaneand doing some bench testing couple things i can not work out...
View ArticleClik here to view.
Camera Gimble Control
@RukusDM wrote: Hi guys. First post here. I've been able to get everything working on the APM 2.6, but I haven't flown the plane yet. Still finishing up details. I have the APM in a Skywalker 1900....
View ArticleReverse trust : which ESC?
@kikislater wrote: Hi, I have an fx61 that it doesn't metter if it crash and I want to test reverse trust.Do someone have a list of working ESC for reverse trust landing ? Of course I have read the...
View ArticleRudder in Auto mode
@torix wrote: I have tried to find information about the rudder is used in auto mode. To me it looks that it only uses ailerons and elevator to line up to the waypoints. Is this true? If so, is it...
View ArticleClik here to view.
Plane dives when transitioning to RTL
@bchristal wrote: Arduplane 3.6Flying wing Seems like this issue has been around for a while, but I've never found a cause or fix. Just built a new plane. Flies perfect - except when it transitions to...
View ArticleQuadplane frame types
@lifepac wrote: Does quadplane support a tail-sitter type frame. The video below is not mine, just an example. I'm surprised these are not the standard type of quadplanes. In the quadplane docs I see...
View ArticleCamera Gimbal Issues
@ripfree wrote: I'm having trouble getting the PAN function on my 2 axis FPV camera to work with my Px4. Everything else is working great....I've flown some long missions. I have ch6 on the RC...
View ArticleGyro Crawl help
@netptl39 wrote: Hi all, I am having a bad gyro crawl on one of my pixhawks running v3.5 and v3.6. I have up and downgraded several times the firmware and still have the issue. Sometimes it forgets to...
View Article