Problem with AUTO MODE
@Dionisisdig wrote: Hi , i have an apm 2.8 (with internal compass) with arduplane 3.4.0 with gps neo m8n ublox with compass. Also I have setup minimosd and telemetry 915mhz kit… The plane flies only...
View ArticleClik here to view.
Airplane landed wrong place without any error meage
@Artem_Skorsky wrote: Hi, for some reason my plane landed in the middle of mission to somewhere , on error messages nothing anyone can help me to understand what caused to this problem ? I have...
View ArticleTilt-rotor quadplane tricopter
@Aticof wrote: How does arduplane consider “Assisted fixed-wing flight” in a quadplane tricopter? I don´t understand somethings questions: First question "Q_ASSIST_SPEED = 0 >>>> because...
View ArticleRedundant RC receivers
@nick2204 wrote: I’m looking for options to use multiple different RF band receivers in order to get RC redundancy in very noisy RF environments. One option would be using a secondary device that...
View ArticleClik here to view.
4G LTE iHAT module
@MRC87 wrote: I recently bought a 4G LTE hat for a RPI from here iHAT. I have an unlimited data plan from verizon wireless here in the US and was going to start playing around with this as a telemetry...
View ArticleClik here to view.
What happen if Radio Rx fails during fly? near crash a new airplane
@cala2 wrote: Today We where doing all checks near to take off with a new airplane, then the Rc died, Mission planner indicate NO RC IMPUT, and servos didn´t respond anymore, no RTL trigger, I...
View ArticleIs compass calibration needed when swapping compass?
@Anthony wrote: If I buy 10 GPS/Compass units (say the M8N here http://www.proficnc.com/system-kits/76-gps-module.html) and I calibrate once. If I swap one unit for another (same set of 10), do I have...
View ArticleClik here to view.
Altitude hold issue in Tilt Wing craft
@Hyori wrote: I am testing a three motor TiltWing craft that takes off as a tricopter. During those tests I am holding it during the whole time, preventing it from getting out of control, but not...
View ArticleTelemetry Login Error
@Nehal_Ahmed wrote: I have an APM 2.5 and downloaded the latest Mission Planner(32-bit) on Win 10 (64-bit). I am not able to connect APM to mission planner using telemetry but able to connect using...
View ArticleData Log Inquiries
@JCPilot wrote: Our team is using the pixhawk autopilot device along with Ardupilot in order to perform an autopilot mission on an unpropelled fixed wing UAV (essentially a glider). We are now at the...
View ArticleGPS show wrong alt at ground
@semo wrote: hi all I am using AP 3.7.1 with GPS ublox 7m But after I turn the plane on in the ground and during the preflight check I see the GPS grow up from 0 to some times 40 sat = 11 hdop = 0.9...
View ArticleAHRS Orientation problem
@alexander_laurie wrote: I am having a problem with the orientation I have a pixhawk mounted upside down and Yawed 90 degrees so it is facing the left side. I think this should be roll 180 yaw 270 or...
View ArticleClik here to view.
Quadplane altitude loss on transition
@frizensami wrote: Hi there, My quadplane keeps losing altitude during its transition to forward flight. It dips about 10 - 15 metres every time it transitions, and I can’t seem to figure out why. The...
View ArticleBad AHRS using new Omnibus F4 Pro HAL
@hurzburg wrote: I am trying to use Night-Ghost’s fork with the new HAL that supports this all in one board. Everything works well on the bench except for one thing. I get consistent bad AHRS if I use...
View ArticleWhy are RC and Servo output min and max and Trim so different
@yak-54 wrote: Hello all how RC and Servo output min and max and trim are different RC1_DZ,30 RC1_MAX,2006 RC1_MIN,988 RC1_REVERSED,0 RC1_TRIM,1494 RC2_DZ,30 RC2_MAX,2006 RC2_MIN,984 RC2_REVERSED,1...
View ArticleAutonomous glider for landing of meteorological radiosondes
@Estario wrote: Hello, We are researching this idea about landing high altitude radiosondes back to where they are launched. Radiosondes are a meteorological equipment, launched with a weather...
View ArticleAutotune PID values not used in FBWA and other modes
@testuser0001 wrote: Hello all, On my Wing Wing z84 I use an APM 2.8 with Arduplane 3.4. I know this is archaic hardware and software. But I have it laying around so why not use it. I have performed...
View ArticleDual motor VTOL delivery flying wing
@Filipkasuba wrote: Greetings everyone, My name is Filip from Croatia and I am in process of developing a dual motor VTOL delivery flying wing. Currently I am still in concept and design phase. I am...
View ArticleAuto take off and landing at different altitudes
@AnthonyV wrote: Imagine the following scenario: I have to fly from a hospital and deliver medicine at a location with different altitude. The hospital is my starting point, so it will be 0 altitude....
View ArticleIs Lidar used as primary height source only during Landing mode or also in...
@lucamax wrote: I need to do a simple mission flying at low altitude , 2 - 5 meters from ground in a flat terrain. But from my tests Lidar seems not to be used. Which parameters should be set to...
View Article