Pixhawk Dronekit Python on Raspberry Pi3 Error with Battery
@rijun034 wrote: I'm using the Pixhawk and Raspberry Pi3 with Dronekit Python.When i'm connecting with Battery, everything is working fine and suddenly after one reboot, with the Battery, the dronekit...
View ArticleClik here to view.
Motor will not arm!
@Sauceman wrote: Appealing to anyone that knows anything or everything, all help massively appreciated! I have gone through the setup process many times and the best I have is 2 servos working but not...
View ArticleApSync RPI Help please
@Barry_Bolton wrote: Hi and thank you for reading. I need someones help in understanding ApSync. Ok so I installed ApSync on my Raspberry Pi and set my RPI in accordance with this...
View ArticleConfiguring Multiple Rangefinders w/ Weighting
@aisaly55554 wrote: I'm attempting to setup two different rangefinders to run on the Pixhawk 2.1 simultaneously. The ArduPlane code has most of the functionality we need already built in. However, I...
View ArticleHttps://discuss.ardupilot.org/t/eagletree-airspeed-sensor-v3-on-px4io/2521
@Karthik_A wrote: Is Eagle tree Airspeed sensor V3 now compatible with Pixhawk 2.1 and AP3.8? Kindly confirm. Posts: 1 Participants: 1 Read full topic
View ArticleFlight controller stuck in an arming check pass-fail loop
@frizensami wrote: Hello there, My Pixhawk 2.1 / Cube on a quadplane has recently been constantly stuck in a pre-arm check failing and passing loop - aka it will report it is ready to arm (flashing...
View ArticleApSync raspberry PI help please
@Barry_Bolton wrote: Any one that can help me with me ApSync? raspberry pi setup please Posts: 1 Participants: 1 Read full topic
View ArticleClik here to view.
Can not setup Wireless Communication to pixhawk
@Sauceman wrote: I can not seem to connect Banggood's FPV Radio Telemetry Ground Module to Pixhawk.I have tried the drivers below where windows 10 says device is working properly but also says that...
View ArticleTalon crash analysis please?
@Graham_Dyer wrote: A friends Talon crashed on launch unexpectedly the other day and he's not sure why, it had flown many times previously without any issues.It was launched in FBW-A mode and the...
View ArticleClik here to view.
EK2_IMU_MASK cannot be set
@artemen wrote: Hi, I have an old pixhawk with a faulty LSM303d, however the MPU6050 (or is is 6k?) is working just fine. In the old AHRS I used to be able to choose active IMU, however when trying to...
View ArticleGPS Fail during Failsafe RTL
@emics wrote: Good morning everyone.I had a problem at the GPS during a flight near my home, I passed under high voltage cables and bumped a cable with the wing of my Bix3.Right after my Frsky X7...
View ArticleDownload SITL firmware for offline use
@semo wrote: Hi all , I want to get the SITL firmwares files for previous releases such as AP 3.7.1 or 3.4 Coz when I use SITL while connecting to the internet I get the latest Firmware 3.8.4 !! I...
View ArticleNo camera feedback on Mission Planner flight data screen
@Verloop wrote: I also posted this message in Mission Planner category, but there was no reply, maybe it is a firmware issue? Up until recently, I used to get camera feedback on the flight data screen...
View ArticleClik here to view.
I2C Sonar Rangefinder
@yak-54 wrote: Any one tried these i have some from a old project srf02-ultrasonic-range-finder-4_1.jpg900x900 83.1 KB I2C CommunicationSRF02 Ultrasonic range finderTechnical Specification I2C ModeFor...
View ArticleEK2_RNG_USE_SPD make no sense to me
@lucamax wrote: The EK2_RNG_USE_SPD with his small possible values of 2.0 - 6.0 meters per second makes no sense to me on a plane. The range finder will not be used as the primary height source when...
View ArticleTower App and flying a fixed wing airplane
@kyoung wrote: I would like to use the Tower app to create and upload missions in a fixed wing airplane. I have used Tower for autonomous flights with my Solo, but never with a plane. I find it...
View ArticleDual motor steering
@Konur wrote: Hello. Is it possible to use arduplane to fly and steer a plane just with two motors? No elevon, no rudder etc. Posts: 2 Participants: 2 Read full topic
View ArticleVer3.8.4 First flight
@hirochi_hirohiro wrote: Flight two times after upgrading from Ver 3.8.2 to Ver 3.8.4. MANUAL, STABILIZE, CRUISE, Return To Launch, Auto, all flew very well. Thank you for your development. Aircraft...
View ArticleIssues loading plane firmware
@kwasi wrote: hi all, i have been trying to set up my PH 2.1 with arduplane firmware. the issue is, the firmware loads, but i am unable to connect the pixhawk to mission planner. and the carrier board...
View ArticleClik here to view.
Estimating GPS vs BARO height - some thoughts
@Jan_Hindoy wrote: My Skywalker X-5 equipped with a MiniAPM 3.1 controller running latest ArduPlane V3.4.0. ALT_MIX is still present in Mission Planner "Full Parameter List", but missing in the...
View Article