JSBSim git repository cannot be cloned
@YehtutHl wrote: Hi everyone, This is my first question here and I'm having problem with cloning git://github.com/tridge/jsbsim.git on ubuntu linux. I'm trying to simulate arduplane, following the...
View ArticleClik here to view.
Airplane wont AutoTakeOff - "Bad launch AUTO"
@legui83 wrote: Hello friends,I need your help since I am lost here and I ran out of ideas. I built a new airplane with Pixhawk 1 with 3.7.1 arduplane firmware. The first flight was good, performed...
View ArticleImpossible Trim in elevon mixing
@Necris38 wrote: Hi ! I'm setting my new FX61 with an APM2.6.I have to trim one elevon in manual mode, so I try to change RC1_TRIM parameter but that does nothing !Of course , if I trim the TX, the 2...
View ArticleSitl always load 3.8.2-dev
@semo wrote: hello fliers , I am trying to simulate my plane using SITL and x-plane10 when I start simulation the Mission planner load 3.8.2 firmware , same thing when I use just Sitl But I want to...
View ArticleNear crash amidst multiple "EKF yaw reset" messages. Logs inside
@rallyon wrote: Hello, I had a mostly good test session of our aircraft yesterday ( see blog for more information). But also experienced some extremely erratic flight behavior. This is not the first...
View ArticleWhere do I configure roll and pitch exponential?
@flyingw wrote: I'm using a Pixracer from mrobotics. For manual flight mode where do I set the exponential values for aileron and elevator in an elevon setup? In the transmitter? Or is there somewhere...
View ArticleFull throttle all time during Flight
@semo wrote: All time I fly my gasoline plane The throttle in FBWA mode while plane fly cruise about = 30-60 % but when switching to Auto all the time throttle 100% why this happen ? Posts: 4...
View ArticleClik here to view.
Quadplane did not transition to QRTL after RTL
@frizensami wrote: Hi there again, I was flying a quadplane that had successfully RTL-ed 3 times already that day. During my last AUTO mission, the quadplane went into RTL mode and flew towards the...
View ArticleClik here to view.
No full Throttle available in FBWA and Acro
@Steffen20 wrote: Hi there, my name is Steffen, I am from Germany. I started with Arduplane nearly 2 years ago, but never flew because of a broken pixhawk lite (no servo output at all). No I have a...
View ArticleClik here to view.
Absolute/MSL Altitude usage
@frizensami wrote: The information about altitude references in Ardupilot/MP feels a little scattered to me, and I was hoping for some clarification on how to use different altitudes to plan missions....
View ArticleAirspeed Ratio purpose?
@John_Swallow wrote: I am trying to understand the purpose of setting airspeed ration to 2 (approximately) for the airspeed sensor I am working with, the MS4525DO. Currently I am using the raw data...
View ArticleClik here to view.
Wing Wing Z-84 Tailsitter Conversion
@Rolf wrote: I have used the little Wing Wing Z-84 for nearly one year with a Pixracer FC and Arduplane with a lot of fun, except not liking the high noise level due to pusher configuration. WW Z-84...
View ArticlePlane 3.8.3beta1
@tridge wrote: I've just released plane 3.8.3beta1. This is a minor release with a number of important bug fixes and somesmall feature additions. Key changes are: allow vertical takeoffs in GUIDED...
View ArticleClik here to view.
Failed to control plane in xplane 10 hil test with qgroundcontrol
@Izmirov wrote: Dear All, I need help with performing hardware in the loop test using QGroundControl (v3.2.4) to virtually fly an aircraft in X-Plane 10. I'm having trouble when arming the system due...
View ArticleClik here to view.
Pitot get covered and near to crash
@korakora wrote: in this case definitely user error (mine) this is for the 1st time i forgoten to uncovered the tube rush but why AP not detect that was a mistake?and keep push the plane to diveis the...
View ArticleWrite the cam log individually in a file
@xvxieweilai wrote: I want to write the cam log in a new file.log file is too big,radio is too slow to download. The write function DataFlash_Class::Log_Write_CameraInfo has been found how to modify...
View ArticleWhy decreased the altitude when RTL?
@korakora wrote: i thought if we get FS (RTL) above the RTL ALT we set, the AP will maintain the current ALT is that correct?why not in this case? it reduce the ALT slowly until RTL ALT instead keep...
View ArticleNon Vectored Tailsitter Planes
@ypsonar wrote: Lot of information discussed on Vectored Tailsitter but I dont found propar key point information on "Non Vectored Tailsitter Planes" In this discuss please share only on Non Vectored...
View ArticleTuning issue. Ignored my pitch command in FBWA
@Gman wrote: Hi, While landing I had odd problem. It was a windy day, and I landed in FBWA as the aircraft was struggling against the wind in AUTO. Approach was good but at maybe a meter or less off...
View ArticleDigital Airspeed MS 4525DO No Value
@aidil wrote: Hello,I have and issues while using MS4525DO digital airspeed that i bought from hobbyking.Using arduplane 3.8.2.Now i'm using 3.8.3 Beta 2 but still cannot using this type of...
View Article