Do you know a mode or a strategy to stabilize the horizontal speed?
@tipehugo wrote: Hi , I'm looking for a mode in which the horizontal speed would be hold and the altitude too. Posts: 1 Participants: 1 Read full topic
View ArticleAltitude problem and Bad AHRS
@mspak wrote: Hi,I've installed Arduplane 3.7.1 into a Pixhawk. Everything seems working fine except the altitude. The altitude fluctuates all time. My plane is stable on my desk and altimeter is not...
View ArticleClik here to view.
How to set the simulation speed on jsbsim via dronekit
@tipehugo wrote: Hi , I'm on droneit using the JSBSIM simulator. I would like to speed up the simulation time. So I 've found the parameter SIM_SPEEDUP. But I don't know how to set it.. I've tried...
View ArticleOffsetting servos to level them out
@ayertay wrote: Hello everyone! How can I change the initial servo position? My flaps are looking up instead of being leveled with the wing. In KK 2.1.5 in Mixing->Offset I can move servo and set...
View ArticleAuto geofencing
@rgillingham wrote: I am new to Arduplane having just found it on the web. I have used geo-fencing as per that found in the HobbyZone sportsman S+ before. With that it worked by applying a fixed...
View ArticleTelemetry Radio status not logged in plane
@Nihal wrote: I'm using plane 3.5.2. Telemetry radio is an RFD900. I have LOG_BITMASK set to log everything. However, when I checked the logs to check the telemetry strength and noise, I didn't find...
View ArticleTaranis channel problems - sticks are wrong
@Jimmy_Oliver wrote: I know this has been covered. I have a Mode 2 Taranis with RETA. The PH requires AETR. I have switched this everywhere I can think of. Mission Planner shows the correct channels...
View ArticleRPM for ICE, hardware and settings
@olboy wrote: Currently with a Pixhawk I have the rpm signal coming into AUX5. With plane3.7 there is a separate RPM input setting under ICE_RPM_CHAN. How do both RPM_TYPE and ICE_RPM_CHAN work...
View ArticleReverse thrust flare transition too abrupt, with rapid pitch up
@mrjadkowski wrote: First, let me give a little background on our aircraft: I have a pixhawk-based flight controller, running a (slightly) customized build of arduplane 3.5.1, that includes a bit of...
View ArticleOffsetting servos to level them out in bicopter
@ayertay wrote: Hello everyone! How can I change the initial servo position? My flaps are looking up instead of being leveled with the wing. In KK 2.1.5 in Mixing->Offset I can move servo and set...
View ArticleControl the max Alieron Angle in Stablize mode
@ahmed wrote: Hi all , I have new Design plane , but I have to control the max roll angle in stab mode , ex. when the roll angle = 35 degree I want the Stab Mode to give the max PWM which is ( 1900 )...
View ArticleClik here to view.
Pixhawk INS Pre Arm Failure
@Mandeep_Singh wrote: Hi, Its been many days i have been trying to arm my pixhawk but it won't arm without disabling pre arms.Arduplane firmware v3.7 and v3.5 both tried. My pre-arm error wont show...
View ArticleMotor Stop, help
@nano1234 wrote: Hi, I have a problem with the engine, when I shut down the RTL mode, the engine stops, and I do not know how to make it work.I have set the motor parameters nimimo, maximum motor in...
View ArticleClik here to view.
APM 2.5.2 firmware verification error
@Jellyfish wrote: Hi,I have this old but in perfect condition APM 2.5.2 which i was trying to update to latest supported firmware but I keep getting verification error message despite the fact that it...
View ArticlePlane 3.7 Radio
@vtran609 wrote: Hi guys, I have a radio issue with my setup. I have a phantom fx-61 setup with the pixracer. When I upload the master build, the radio works fine. I can configure my elevon and...
View ArticleEKF, EK(F)2, EK(F)3, etc. What is the difference
@Patribus wrote: Hello, I'm new to Pixhawk and are presently setting up a fixed wing. I'm comparing the parameters of my Pixhawk with another one, which I have available and I have a question about...
View ArticleServo over CAN or RS232
@MattCoden wrote: Hello everyone! I'm looking into an option to control MGL Avionics servos from Pixhawk - http://www.mglavionics.co.za/servo.html...
View ArticleList of abbreviations (e.g. BRD)
@Patribus wrote: Hello, I'm new here and I'm setting up a fixed wing based on the Pixhawk. I'm having a hard time to find the meanings of a lot of abbreviations, such as BRD, just to mention one. Is...
View ArticleAutotune throttle issue
@kas219 wrote: I recently had an issue while trying to run autotune during a flight. After switching from FBWA to Autotune, the throttle went to zero and I could not bring it back up. It stayed like...
View ArticleAirspeed Sensor Variance
@paan2097 wrote: I'm having serious problems with airspeed sensors. I'm running ardupilot 3.6 on three fixed wing build and my airspeed sensors are completely out of sync. Before every flight I before...
View Article