SERVO_AUTO_TRIM both ailerons up
@robothornet wrote: Hi all, After a long time of trimming new planes manually and then using the TRIM_AUTO param, I decided to give the SERVO_AUTO_TRIM a try. The outcome is a bit puzzling, since...
View ArticleProblem with Tilt Rotor setup
@Carlo_b4 wrote: Hi everyone I’m searching for how to do the tilt rotor setup (I refer to the guide https://ardupilot.org/plane/docs/tilt-rotor-tips.html). I can’t understand the guide… Reading it...
View ArticleUse a different motor for the back motor of a tricopter VTOL
@spetsnaz26 wrote: Can I use different motors in a tricopter tiltrotor setup? I wanna use a Tmotor MN4012 kv400 for the back rotor of a tiltrotor I’m building. The front motors are Sunnysky X3120s....
View ArticleMSG, Tuning: error 1.04
@iter wrote: I tuned on transmitter-based tuning, and my log is full of lines like this now: MSG, 319548646, Tuning: error 1.04 What does this message mean? Ari. Posts: 1 Participants: 1 Read full topic
View ArticleTo control a plane with jet engine
@liaohui wrote: I need Arduplane to control a jet plane,it’s speed will be more than 250KM/H（Conventional fixed wing）. And I want to use the AUTO mode to fly a Specific line,can it keep...
View ArticleQplane (TriCopter layout) motor response
@Wandert wrote: Mechanically build went fine, however during the first QSTABILIZE flight test i discovered that the motor response on pitch stick inputs was reversed on all motors. Throttle response...
View ArticlePlane Simulation SITL Error
@mufasa wrote: Hello, Yesterday i could use Plane v4.0 Simulation but after the latest software update it started to give the error: “Failed to connect to SITL instance.” I asked some of my friends...
View ArticleFuriousFPV F35 Arduplane Nano Talon Setup
@actionplus wrote: I’ve pretty much everything working on the board. All works fine, but the compass does not seem to want to calibrate. I can get the first progress line to go all the way to the end...
View ArticleClik here to view.
Quadplane - height gain during VTOL to FW transition
@kelvinc wrote: Hello, Would anyone be able to help me out with this one? This occurred in one of our flights where we conducted a transition from Q_Loiter to Cruise. Started at 86m but then the...
View Article[HELP] Setting up radio CRSF
@WeissMISFIT wrote: Hey ya’ll, I’m using a matek F765 with crossfire and I’m struggling to get my crossfire nano to show up on the receiver calibration tab. I’ve tried using SBUS, Mavlink Tx and Rx,...
View ArticleFailsafe Function
@viper16 wrote: Hello everyone, i would like to ask about failsafe function. When the rc signal loss, is it possible for the plane to cutt the throttle and drop itself with the movements of elevators,...
View ArticleLog missing XKF3 data
@andyp wrote: Hi My logs save to sd card contain XKF2 data, but no XKF3 data. Any idea how to configure for XKF3? Thank you! Posts: 1 Participants: 1 Read full topic
View Article4+1 VTOL blade position in cruise
@zaumo wrote: I couldnt find any parameter/info on how to control the copter props, so that they stay longitudinal during cruise. As far as I know, a PWM signal controls the RPM of the ESC-motor. Can...
View ArticleACRO Mode in Yaw Axis
@majorpr13 wrote: Does anyone know if there exists a way to command rates over all the axis in arduplane? If not through mavlink, I know the acro mode has rate control in the pitch and roll axis…is...
View ArticleClik here to view.
[HELP} - Need stable loiter
@Lynchkp72 wrote: For a project I am working on, we need a very stable loiter. I notice I have an AltErr and the plane is oscillating while in loiter, about 10-15 meters and speed is varying as well....
View ArticleTiltrotor Y3 config question: permanent rear rotor forward tilt necessary or...
@spetsnaz26 wrote: so i read the tiltrotor and qplane doc a few times over and understand it is suggested to set two tiltable rotors’ ‘straight up’ position slightly tilted forward so that the...
View ArticleQuadplane Severe Vibration
@gxryy wrote: My Quadplane keeps vibrates severely when its at 20% throttle. I am using Pixhawk 4 with Quad enabled. I have enclosed the video and log file of the vibration. Perhaps someone could give...
View Article4+1 Quadplan (Foxtech Loong) Radio Modes
@Chris_Heintz wrote: Hi all, I just acquired a Foxtech Loong and am looking at setting up the radio (Taranis) for various flight modes. With past fixed wings, we had a 3 position switch with 3 modes...
View ArticleClik here to view.
Plane doesn't descend in turns under Guided control
@Leon_Fargher wrote: Hi all, I am controlling a plane in guided mode using dronekit, for mission control and complex routes. I have noticed that when the plane is turning/banking (not level) it...
View ArticleClik here to view.
Tiltwing VTOL Trim parameter reset
@Bart989 wrote: This is my first post, so Hello! I have tiltwing configuration with whole wing moving with motors, and back motor with yaw servo, as standard tiltrotor configuration. I have a first...
View Article