Clik here to view.
PH4 mini tilt motor issue
@geoffreybainathsah wrote: Hi I’m facing an issue with my ph4 mini. I have it set up on a fixed twin motor tilt rotor. My issue is that any port assigned to function 75 and 76 (lilt motor left and...
View ArticleF4pro V2 can't recognize receiver signal
@ALEX007 wrote: Such as the title I flashed the firmware in the first time when F4 Flight Control ported APM，At that time, the RX is still working normally on there. But after the last upgrade, I can...
View ArticlePlane was behaving abnormally in auto modes.(Log Attached)
@ninja_zx11 wrote: Hi all, My Easystar-II with OmnibusF4ProV3 was behaving abnormally after i switched from FBWA to loiter and cruise mode.It was trying to stall.Then i landed it and took off again...
View ArticlePossible/Likely Bug is Servo_Autotrim
@Marc_Dornan wrote: I have some very odd behavior when I set SERVO_AUTO_TRIM to enable on my Nano Talon flying the latest release of 3.9 on an Omnibus F4 Pro V3. At some point in the flight, often at...
View ArticleX-Plane 11.33r2 not receiving commands
@TunaLobster wrote: I can get X-Plane to output data and mission planner and mavproxy display it. The data is not working the other way. I checked that I am using the ports that are defined in the...
View ArticleFor Holybro pixhawk 4. Which port should be connected to the digital air...
@egunak95 wrote: I2C Buses • the internal I2C port is bus 0 in ArduPilot (I2C3 in hardware) • the port labelled I2CA is bus 3 in ArduPilot (I2C4 in hardware) • the port labelled I2CB is bus 2 in...
View ArticlePixhawk Lite - with ChibbiOS FW Win10 driver error
@pauljatherton wrote: Just dug out my old fx61 which has a Pixhawk Lite FC installed (fmuv2 I believe). This has the older 3.8.5 NuttX firmware installed and connected to MP no probs (running in...
View ArticlePlane powered up after weeks being off, all RCx_TRIM values changed?
@Graham_Dyer wrote: Just had the weirdest thing. Took our plane (Nimbus 1800 VTOL) for a flight after a few weeks of no flying. Plane had flown fine the last time and hadn’t even been booted up since...
View ArticleCan I download a log in flight via Mavlink to my PI3?
@Brian_Duvall wrote: Hello all, I see that there are messages to get logs on the Mavlink site but I don’t understand how to use them. More specifically this message: LOG_REQUEST_LIST Any examples...
View ArticleDSHOT protocol in ArduPlane 3.9.8
@maciek252 wrote: I can’t find any parameter for configuring DSHOT mode in ArduPlane 3.9.8. None of these described in the ArduPlane docs are present among my parameters. [MOT_PWM_TYPE],...
View ArticleAdvice needed - Quadplane and big props
@Roby wrote: Hi, I’d like to try quadplane using Cube and big props setup like 27"-29". Any advice for the start, procedure and settings (parameters, tuning)? I intend to use FW 3.9.8 and manual tune...
View ArticleLocking propellers at certain angle in fixed wing mode flight for quad planes
@ishmaelfarai wrote: Hi Guys, Still busy with my quad plane build project, wanted to find out if anyone has any knowledge of configuring in mission planner propellers to be locked at a certain angle...
View ArticleClik here to view.
Arduplane 3.10 dev
@Matt_C wrote: I know this is in the 3.9 category but figured I’d throw up a log of two flights of a nimbus I had sitting in the closet for a cpl years. Figured I’d post them in case there is...
View ArticleTakeoff throttle not 100%
@reluctantgithubuser wrote: THROTTLE_NUDGE off STICK_MIX off on autolaunch, only get 94% throttle, even though THR_MAX and TKOFF_THR_MAX both set to 100% with THROTTLE_NUDGE on and full throttle on...
View ArticleQuadplane RTL error
@darrell wrote: I’ve been out testing a new build of a Skywalker X8 quadplane and it’s been flying great! Yesterday I was testing battery low voltage tripping a failsafe set to RTL. The plane flew...
View ArticleHelp plane diversion
@ihsan215 wrote: Hi , my fixed wing aircraft are mechanically full of trims and i used pixhawk cube 2.1, dynamics and responses are fine in manual mode but in the fbwa mode the aircraft diversion to...
View ArticleFlight controller
@Syliaz wrote: Hello, I’m looking to put an autopilot on my plane, which will communicate with ez wifibroadcast. However, I find many flight controllers without differences, except the price. What is...
View ArticleGauges on APM Planner 2, and PFD
@tintin wrote: How do i get Gauges on APM Panner v 2.0? I have Mac OS. APM Panner v2.0.27-rc1 Also i like the Prim Flight Display from V1.0, is there anyway I can get the old one? The Prim Flight...
View ArticleThrottle active on power up!
@Shane_R wrote: Just moved to 3.9.8 and discovered a major safety issue. If the plane is powered up and the transmitter is in Manual mode with the throttle raised the plane engine will run while...
View ArticleClik here to view.
Baro altitude problem
@kd0aij wrote: baro pressure looks good, but the altitude is very wrong… Plane master and PixRacer image.png1087x585 55.8 KB Posts: 1 Participants: 1 Read full topic
View Article