Quadplane Transition Done (and then issues with second attempt!)
@jacques_eloff wrote: I did some transition flights today – the first went down perfectly well. However on the second, something strange happened: Once transition was achieved (in FBWA mode) I started...
View ArticleAdvice on Trim [porpoising] not related to PIDs, FLYING wing setup
@raptor wrote: I have a flying wing and while there probably is a small issue with structural flexing between the fuselage and the high aspect ratio sweep wings looking at the log I wonder if there is...
View ArticleStill need to set COMPASS2_USE to 0 to be able to ARM :(
@marcmerlin wrote: I have a pixhawk and a pixfalcon in 2 different airframes.Neither will arm because of "compass inconsistent".I think this started in 3.5, but not sure anymore. I've just had to...
View ArticleClik here to view.
Is there any android app that will replay a tlog and show a GPS track?
@marcmerlin wrote: I've tried tower, I've tried the old droidplanner 2, I've tried andropilot.They all record a tlog, but I was not able to get any of them to replay that tlog or even just show me a...
View ArticleBuild failed: AP_GPS_NMEA.cpp:error: 'INT32_MAX' was not declared in this scope
@ChaosSeeker wrote: Hey there. When I ran the sim_vehicle.sh -w command I got an error, which cause the build to fail. AP_GPS_NMEA.cpp:error: 'INT32_MAX' was not declared in this scope After...
View ArticleUBLOX M8 - different performance with PLANE and COPTER
@around wrote: I have two identical Pixhawk clones on the bench, one running Copter V3.3.3 and one running Plane V3.6.0. I was testing a new Ublox M8/compass GPS module and noticed a significant...
View ArticleClik here to view.
Quadplane total loss of control in FBWA leads to catastophic crash
@iskess wrote: I had my 3.6 quadplane flying so nicely tonight, but it ended in a crash that totaled the plane. I was flying around at about 30m in FBWA when the controls became ineffective. Looking...
View ArticleQuadplane output frequency in octa-quad mode's problem
@Kiddy wrote: Guys I have test quadplane very well. Recently I want use octa-quad mode to fly, but I find all the outputs (1 to 12) at high PWM rate (400Hz) include 1 to 4. I use the initial settings...
View ArticleClik here to view.
BBBMINI - Arduplane error at startup
@ppoirier wrote: Hello, I know it is a question for Mirko, but he is not available for the moment and I cant wait to fly So I just cross-compiled my Arduplane with these:git checkout ArduPlane-3.6.0...
View ArticleQuad plane question
@Barry_Bolton wrote: Is it possible to assign a Y6 configuration to quadplane or can it only do x configuration? Posts: 1 Participants: 1 Read full topic
View ArticleExtra Flight mode Channels As in Arducopter are they hidden in Arduplane
@Paul-H wrote: Hi all In Arducopter you have more than one channel used to switch modes, 5 for most modes and 7 & 8 for extra mode options. In Arduplane I can only find one, CH8 is there a hidden...
View ArticleUsing Ardupilot on a large gas fuel engine UAV
@alireza_ghaderi wrote: HiSorry if my question is silly . I wanted to know if it is possible to use APM on a UAV with a large non-electric UAV? what modification should i do for that? Posts: 2...
View ArticleY configuration Quadplane?
@Barry_Bolton wrote: Morning everyone. Is it possible to set up a Y configuration for quad copter instead of the normal X configuration. Posts: 1 Participants: 1 Read full topic
View ArticleCan't get the plane off the ground
@RoverHunter wrote: I have just build the code using cygwin acording with the tutorial made by tridge on Using SITL with your own GCS.After this I have openned Mission Planner 1.3.39 build...
View ArticleClik here to view.
QuadPlane cut the throttle automaticly in Qloiter mode and crash(3.6)
@farstein wrote: Hello,friends, hoping your help.When my QuadPlane fly to a certain alt(always some meters) in Qloiter mode, ardupilot will always slowly decrease the output of RC5/6/7/8,and so plane...
View ArticleConstant Beep from motor until safety button is pressed?
@Paul-H wrote: Hi Just setting up my first plane using a Pixhawk and noticed that the motor constantly beeps until I press the safety button. Is this indicating a problem or normal in Arduplane, I am...
View ArticleUsing UART2 to output FrSky telemetry along side Mavlink on UART1
@kinghaigy wrote: I'm trying to follow this guide: http://ardupilot.org/copter/docs/common-frsky-telemetry.html#native-frsky-telemetry-support I've got the hardware hooked up exactly as it is in the...
View ArticleGlider control mode?
@Dimitri_S wrote: I was wondering if anyone has a recommended approach to glider control? I know previous work has been done with thermal finding by some, however I wanted to experiment with it myself...
View ArticleClik here to view.
Arduplane 3.6 Quadplane - PIxhawk PX4 experiencing erratic motor using...
@JeffBloggs wrote: Hi there fellow Quadplane pilots!This is my first post in the new forum, and I'll en-devour to respond daily. I've been flying quadplanes/derivatives since the beginning of 2015...
View ArticleQuadplane landing issue using weathervaning, Quad hover and forward motor...
@JeffBloggs wrote: I think there might a potential problem with the current quadplane code using both quad and forward motor at the same time whilst in position hold and trying to land. The issue can...
View Article